Bedienungsanleitung Festool DSC-AG 125 (Seite 23 von 126) (Alle Sprachen)

778812

Zoom out

Zoom in

Vorherige Seite

1/126

Nächste Seite

9.2 Motor electronics

Starting current limitation

Electronically controlled continual running se-

cures device acceleration without back thrust.

Due to starting current limitation in the device,

16A protection is sufﬁ cient.

WARNING

Devices without starting current limitation

need higher protection – at least 16A circuit

breaker.

Speed control

You can regulate the speed steplessly within the

speed range using the adjusting wheel [1-15] (see

Technical data). This enables you to optimise the

speed to suit the respective material. Please also

note the speciﬁ cations on the tools.

Switching off during back thrust

During sudden drop of revolutions, for example

blocking in dividing cut, the current input in mo-

tor stops. For re-starting, the device must be ﬁ rst

switched off and again switched on.

Protection against re-starting

Prevent uncontrolled starting of the device after

current supply cut off. For re-starting, the device

must be ﬁ rst switched off and again switched on.

Constant speed

The preselected motor speed remains constant

through electronic control to ensure a uniform

cutting speed even when under load.

Protection from overloading dependant on tem-

perature

The safety electronics switches to cooling regime

when the critical temperature is reached. Motor

continues running at approximately 50 % revolu-

tions, constant electronics is deactivated.

After cooling to approximately 10 – 20 s, the device

is fully operational.

Heat protection for devices heated during opera-

tion, reacts adequately sooner.

9.3 Turning the gear box

For special cases, the gearbox can be turned in

steps of 90°. This achieves a better handling posi-

tion of the switch.

For such work, we recommend to use the Festool

service.

Remove four screws.

Carefully, turn the gearbox into required posi-

tion. Make sure the gearbox does not separate

from motor box by more than approximately

1mm.

Insert and fasten the four screws -ﬁ gure [8].

9.4 Aperture cover

If you wish to see the cutting area, take off the

aperture cover [2-3]. Only handle this cover when

the disc is not running.

Be careful about spattering dust particles.

10 Service and maintenance

WARNING

Risk of accident, electric shock

Always pull the plug out of the socket before

performing any type of work on the machine.

All maintenance and repair work which re-

quires the motor housing to be opened, must

only be carried out by an authorised service

workshop.

- Wrapped electric tools can be stored in a dry

place without heating, with temperatures not

lower than –5°C. Unwrapped electric tools can

only be stored in dry places with temperatures

not lower than +5°C, without sudden changes

in the temperature.

-To ensure the airﬂ ow is sufﬁ cient, cooling

openings of the motor must be always clean

and free.

-The machine is equipped with special self-

disconnecting brushes. When the brushes are

worn, the power supply is automatically discon-

nected, and the machine is stopped.

-If the suction ﬂ ange height adjustment system

does not operate smoothly, the ﬂ ange must be

removed and cleaned.

Customer service and repair. Only through

manufacturer or service workshops:

Please ﬁ nd the nearest address at: www.

festool.com/service

EKAT

235

Use only original Festool spare parts! Or-

der No. at:

www.festool.com/service

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool DSC-AG 125 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info