Bedienungsanleitung Festool EHL 65 E (Seite 9 von 54) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

498031

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

Smooth start-up

The smooth start-up ensures the router starts

up jolt-free.

Constant speed

The pre-selected speed remains constant whether

the machine is in operation or in neutral position.

Temperature control

To prevent overheating, the safety electronics

switches the machine off when it reaches a critical

motor temperature. Let the machine cool down

for approx. 3-5 minutes before using it again. The

machine requires less time to cool down if it is

running, i.e. in neutral position.

5 Chip thickness adjustment

The planing depth can be adjusted by turning the

rotary knob (2.1) (turn to the right = larger planing

depth, turn to the left = smaller planing depth).

The planing depth which has been set can be read

at the mark (2.3) for the rotary knob scale (2.2).

Adjustment by one scale mark corresponds to a

change in planing depth of 0.1 mm.

The max. planing depth is 4 mm. So as no to

overload the machine, we recommend that a

maximum planing depth of 2.5 mm be set with a

plane width > 40 mm.

6 Changing cutters

Use only cutters which are sharp and

undamaged. Blunt cutters increase the

danger of kick-back and reduce the plan-

ing quality obtained.

- Always disconnect the mains plug from the

socket before changing the cutter.

- Loosen the locking screw (2.9) by approx. 2

revolutions with the Allan key (2.6) and remove

the cutter from the cutter shaft.

- Clean the cutter slot before inserting the new

cutter to ensure a correct ﬁ t.

- Then insert the new cutter (488 503) into the

groove with the printed side facing the rear

planer platen (2.8).

- Before tightening the locking screws (2.9) align

the cutter with a ruler so that its front edge

(1.13) is ﬂ ush with the sides of the front (1.12)

and rear (1.14) planer platens. Then tighten ﬁ rst

the central locking screw, followed by the two

outer screws.

7 Dust extraction

The standard equipment for the planer

includes devices to enable the planer to

be used with both the chip collecting bag

(1.1) (accessories) (488 566) or a suction

hose (1.2) (accessories) connected to a

dust extractor.

The connector for dust extraction can be ﬁ tted

on either side of the tool. To change sides, press

the toggle lever (1.11) down ﬁ rmly. This releases

the lug on the outer edge of the casing and the

adapter (1.4) can be pushed through the casing

(Fig. 3). The adapter (1.4) can now be inserted

into the casing opening (4.1) lug ﬁ rst up the stop

in the casing.

Either the chip collecting bag (1.1) or an angle

piece (1.3) for a suction hose adapter (1.2) can be

ﬁ tted to the adapter (1.4). The chips can be de-

ﬂ ected in any direction by turning the angle piece.

A suction hose Ø 27 mm adapter is inserted into

the angle piece (1.3). A suction hose Ø 36 mm

adapter is ﬁ tted over the angle piece (1.3).

8 Putting the planer down

When working with electric planers you must

remember that the planer shaft continues to run

for a few seconds after the tool is switched off.

The EHL 65 E has a support foot (2.7) at the end

of the platen so that it can be placed safely on a

work surface. If the electric tool is taken up, the

support foot automatically protrudes beyond the

planer platen to ensure that the planer shaft is

always raised above ﬂ at work surfaces when the

planer is put down.

Pay attention to the following when put-

ting the EHL 65 E down:

- check that the support foot is present and fully

operational,

- wait until the planer shaft comes to a standstill

before putting the tool down.

If the support foot should be found obstructive

during special planing work it can be swung back

out of the way and locked in position.

9 Fitting the guides

9.1 Rebating depth guide (488 543)

The rebating depth guide (1.8) is mounted in the

threaded hole (1.10) on the front right of the ma-

chine.

The stop can be inﬁ nitely adjusted to between

0 and 23 mm in accordance with the scale. The

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool EHL 65 E Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info