778531
24
Zoom out
Zoom in
Vorherige Seite
1/143
Nächste Seite
Cutting depth without guide rail/track
rail
max. 55 mm
+FS
Cutting depth with guide rail/track rail
max. 51 mm
7.3 Adjusting the cutting angle
The saw table must be on an even surface
when adjusting the cutting angle.
Between 0° and 50°:
Open the rotary knob [4-2].
Swivel the saw unit to the required cutting
angle [4-1].
Close the rotary knob [4-2].
Both adjustments (0° and 50°) are set at
the factory and can be readjusted by the
customer service team.
For angled cuts, the cutting depth is
smaller than the value displayed on the
cutting depth scale.
7.4 Adjust pendulum guard
CAUTION
Risk of injury! Sharp edges!
The pendulum guard swings back quickly in
the event of sudden release.
The pendulum guard [1-6] must only be
opened with the retractor lever [1-4].
7.5 Selecting the saw blade
Festool saw blades are identified by a coloured
ring. The colour of the ring represents the ma
terial for which the saw blade is suited.
WARNING! Risk of injury! Pendulum hood
mechanism not working correctly! Diamond
saw blades must not be used to saw cement-
bonded fibreboard.
Colour Material Symbol
Yellow Wood
Red Laminate, mineral ma
terial
HPL/TRESPA®
Green Plaster- and cement-
bonded chipboard and
fibreboard
Blue Aluminium, plastic
"$3:-
7.6 Changing the saw blade
WARNING
Risk of injury
Remove the battery pack from the power
tool before performing any work on the
power tool.
CAUTION
Risk of injury from hot and sharp insertion
tool
Do not use any blunt or faulty insertion
tools.
Wear protective gloves when handling an
insertion tool.
Removing the saw blade
Swivel saw to 0° position before replacing
the saw blade and set maximum cutting
depth.
Position saw on motor cover when replac
ing [5-1].
Turn the lever [5-4] as far as the stop.
Open the screw [5-8] using the Allen
key [5-3].
Hold the pendulum guard open [5-7] only
with retractor lever [5-5].
Remove the saw blade [5-9].
Inserting the saw blade
WARNING! Check the screws and flange for
contamination and only use clean and undam
aged parts.
Insert the new saw blade.
WARNING! The direction of rotation of the
saw blade [5-10] and saw [5-6] must
match. Serious injuries may occur in the
event of non-compliance.
Insert the outer flange [5-11] so that the pin
engages in the recess on the inner flange.
Release retractor lever [5-5] and allow the
pendulum guard [5-7] to swivel back to its
final position.
Tighten the screw [5-8].
Reposition the lever [5-4].
English
24
24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Festool HKC 55 EB wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info