778626
16
Zoom out
Zoom in
Vorherige Seite
1/108
Nächste Seite
4 Technical data
Cordless oscillator OSC 18
Motor voltage 18 V
Speed 10,000–19,500 rpm
Oscillation angle 2 x 2.0°
Tool holder
Compatible with
StarlockMax
StarlockMax/
Starlock
Plus/Star
lock
Compatible with battery packs
from the series BP 18
Weight as per EPTA procedure
01:2014: 1.6 kg
5 Parts of the device
[1-1] Clamping lever for changing tools
[1-2] On/off switch
[1-3] Gripping surface
[1-4] Cooling air openings
[1-5] Capacity display
[1-6] Capacity display button on battery
pack
[1-7] Button for releasing the battery pack
[1-8] Battery pack
[1-9] Speed control
[1-10] Tool
[1-11] Adapter*
[1-12] Depth stop with sliding shoe*
[1-13] Rotary depth stop*
[1-14] Dust extraction device*
[1-15] Positioning aid*
* Accessories shown or described are not al
ways included in the scope of delivery.
The illustrations specified are located at the be
ginning and end of the operating instructions.
6 Commissioning
6.1 Switch on/off
The switch [1-2] is an on/off switch (I = ON, 0 =
OFF).
When the battery pack is empty, or if there
is a power failure or the mains plug is re
moved, move the on/off switch immediate
ly to the Off position. This prevents uncon
trolled restarting.
7 Battery pack
Inserting the battery pack [2a]
Removing the battery pack [2b]
7.1 Capacity display
The capacity display [1-5] indicates the charge
of the battery pack for approx. 2 seconds after
the button [1-6] is pressed:
70‑100%
40‑70%
15‑40%
< 15% *
* Recommendation: Charge the battery pack
before any further use.
Further information about the charger and
battery pack with capacity indicator can be
found in the corresponding operating
manual.
8 Settings
WARNING
Risk of injury
Remove the battery pack from the power
tool before performing any work on the
power tool.
8.1 Speed control
You can use the adjusting wheel to continuous
ly adjust the speed within the speed range (see
Section Technical data). This enables you to op
timise the speed to suit the respective material.
Please also note the specifications on the tools.
If an insertion tool is only suitable up to a maxi
mum speed, the maximum speed [14-1] is
marked on the insertion tool (see Fig. [14]).
English
16
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Festool OSC 18 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info