778626
17
Zoom out
Zoom in
Vorherige Seite
1/108
Nächste Seite
8.2 Changing the insertion tool
CAUTION
Hot and sharp tools
Risk of injury
Do not use any blunt or faulty insertion
tools.
Wear protective gloves.
Carefully remove the protective resin from
the cutting edge of new tools.
CAUTION
There is a risk of injury and negative impact
on health associated with using tools that
are not supplied or recommended by
Festool.
Damage to machine caused by increased vi
bration load
Always use original Festool tools.
CAUTION
Risk of crushing hands and fingers
If you switch on the power tool when the
clamping lever is open, the clamping lever is
closed by spring force. Open clamping jaws
are spring-loaded.
Never switch on the power tool with the
clamping lever open.
Never reach into the area around the
clamping jaws.
Removing the insertion tool [3a]
Open the clamping lever [3-1].
The insertion tool drops down.
Close the clamping lever until it clicks into
place.
If the power tool switches on without the
insertion tool, the clamping jaws [3-2] may
open. This makes a popping sound.
Inserting the insertion tool [3b]
If the clamping jaws [3-2] are open, open and
close the clamping lever [3-1].
Close the clamping lever until it clicks into
place.
Push the device onto the tool until it clicks
into place.
The tool can be offset in 30° increments
and secured in the most effective working
position.
The protection (against accidental contact)
on the saw blade may become twisted if
wear has occurred, see fig. [4]
9 Working with the machine
Observe the following information:
Only guide the power tool towards the
workpiece when it is switched on.
A significant increase in the force required
to advance the machine and slow working
progress are indicators that the blades are
worn.
Hold the power tool by the gripping sur
face [1-3] with both hands to ensure safe
guidance. Do not cover the cooling air
openings [1-4] with your hand. Otherwise
there is a risk of the machine overheating.
Do not hold the power tool by the battery
pack.
Always secure the workpiece in such a way
that it cannot move during machining.
10 Acoustic warning signals
If the power tool switches off due to one of the
following operating states, a warning signal
sounds when switching on the tool and the
power tool switches off again.
Battery pack not accepted
Insert the correct battery pack model.
Battery pack empty
Change the battery pack.
Charge the battery pack.
Battery pack fault
Change the battery pack.
Use the charger to check that the battery
pack is fully functional once it has cooled
down.
Battery pack overheated
Let the battery pack cool down.
Power tool overheated
You must allow the power tool to cool down
before starting it up again.
Power tool fault
Contact a Festool service workshop or spe
cialist dealer.
Power tool jammed
Eliminate the cause of the jam.
If the power tool switches of when it be
comes jammed, no warning signal sounds.
English
17
17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Festool OSC 18 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info