574995

Festool PALLAS50 Seite 11

11
Zoom out
Zoom in
Vorherige Seite
1/59
Nächste Seite
@
1
Scope
of
delivery
"Basis
1 AfT"
work
module
1.1
Portable circular saw guide
1.2 Bolt
to
fasten the riving knife
to
the "Basis Plus"
base
1.3 Protective cover with support
1.4 Switch
clip
1.5 Bolts
to
fasten the guide handle to the "Basis
Plus"
1.6 Guide handle
1.7 "Basis WRA
500" mitre fence
"Mod
1 A / ATF 55
E"
trim
saw
module
The "Mod 1
AI
ATF
55 E" trim saw module consists
of the "Basis 1
AlT'
work module
and
the
ATF
55 E
portable circular saw (already litted belore delivery).
"Basis
1
A"
Basis-Set
The "Basis 1
A"
Basis-Set consists
01
"Mod 1 A /
ATF
55
E"
the trim saw module and "Basis Plus" base unit.
"Palfas
50"
Basis-Set
The
"Pallas 50" Basis-Set consists of the "Basis 1
AI
T" work module, the
ATF
55 portable circular saw
and "Basis
Plus" base unit without loldaway legs.
2 Technical data
Max. length
01
cut (as trim saw)
Length of cut (as trim saw)
at
12
mm thickness
Cutting depth
- at 90" position
- at 45" position
Bevel adjustment
Tablesize
Table
height
- with foldaway legs
- without foldaway legs
Weight
3
Correct
use
240mm
230mm
0-50mm
0-33mm
0"-45"
650
x
495mm
820mm
310mm
26
kg
The "Basis 1 AlT" work module
is
used to lit the
Festool portable circular
ATF
55,
ATF
55 E or ATF 55
EB.
Other portable circular saws may not be used
lor safety reasons.
The "Basis 1
AlT" work module and "Mod 1 A /
ATF
55
E"
trim saw module have been designed for cor-
reet
use and installation
in
the "Basis Plus" base
unit.
The "Basis 1
A",
"Pallas 50" Basis-Set has been
designed to cut wood, wood-like materials and pla-
stics in consideration of their technical data.
If the
portable circular saw is fitted with Festool saw blade
439686
it
can also be used to cut aluminium.
The "Basis 1
A",
"Pallas 50" Basis-Set can be opera-
ted
by one person. The working position
is
in
front of
the table to the left of the saw (Fig.
16
and 17).
The "Basis 1
A",
"Pallas 50" Basis-Set should not be
operated or stored outdoors or
in
a wet environ-
ment.
The users shall be liable for damages and accidents
due to incorrect use.
4 Please read before
starting
work
4.1
Safety
instructions
Pie
ase
read the following salety instructions, the
safety instructions on the enclosed leaflet
and
the
operating instructions for the portable circular saw
before starting work
- Check that the saw
is
fastened properly
in
the
work module and that the work module
is
fixed
to
the "Basis Plus" before starting the tool
-
If
used
as
a trim or bench saw the protective
cover and support must be fastened
to
the guide
( Exception: concealed cuts) The protective cover
must
be
lowered workpiece.
- The workpieces must always be guided with or
laid against a stop.
- Keep a safe distance away from moving saw bla·
des: keep your fingers together when working.
Use a guide handle for longitudinal cuts
in
work-
pieces narrower than
120 mm.
00
not remove
loose splinters, chips and similar materials from
near the moving saw blade with your hands.
- Ensure that cuttings
are
not caught
in
the teeth of
the saw blade and
Ily off in all directions.
- The "Basis 1
A",
"Pallas 50" Basis-Set may not
be
used
to
cut firewood.
- Circular wood must be held on both sides
of
the
saw blade when cutting
to
stop
it
from twisting.
- The table
of
the guide unit may not display any
damages, e.g. nicks on the saw gap.
II
it
does,
have this replaced
by
the Festool service depart-
ment.
- Support long workpieces on the delivery side.
4.2 Residual
risks
Risks may still arise despite the observance or
all
building regulations, e.g. through:
- workpiece parts flying off,
- damaged tool parts flying off,
- wood dust emissions,
- noise emissions.
5
Construction
5.1
Setting
up
the
"Basis
Plus"
base
unit
("Palfas
50"
Basis-Set
without
foldaway
legs)
The foldaway legs (2.1) are screwed
in
pi
ace at the
joints (2.5) after unfolding.
The "Basis Plus" base unit should be placed
on
firm,
smooth base. Adjust the
bevelled caps (2.2)
on
!wo
legs so that the "Basis Plus" base unit does not
wobble.
Screw the bolts (1.5) into the threads (3.2),
so
that
the guide handle can be hung on these.
5.2
Locking
the
connecting
rod
The connecting
rod
is
released
by
pressing lightly
against the handle (4.1) and can then
be
pulled for·
wards. The connecting rod can
be
locked
in
!wo
positions with the lever (4.3):
- Groove (4.4) = front position,
- Groove (4.2) = rear position.
11
… 11 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Festool PALLAS50 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info