Bedienungsanleitung Festool PALLAS50 (Seite 12 von 59) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

574995

Zoom out

Zoom in

Vorherige Seite

1/59

Nächste Seite

5.3

Fitting

the

portable

circular

saw

the

"Basis

Arr"

working

module

Warning:

not use lorce during installation since

this could damage parts

the portable circular saw

or the working module!

Place guide unit upside down "Basis Plus"

(Fig.5).

- Lock connecting

rod

rear position.

- Turn the support lor the portable circular saw

lully

up with the crank

(6.1).

- Open rotary knob (6.6) and swivel support to a

45° position with the handle (6.2).

- Unscrew locking bolt (7.3) and unscrew rotary

knob (8.2).

- Inset portable circular saw

shown

Figure

The pin (7.2) must

inserted into the groove

(7.1)

the portable circular saw and the clamping

plate

(8.1)

should rest against the portable circu-

lar saw.

- Tighten locking bolts (7.3).

- Fasten portable circular saw with rotary knob

(8.2) to clamping plate

(8.1).

- Release plunge lock (6.5)

the portable circular

saw,

slide support (6.3) onto the handle

the

portable circular saw and tighten rotary knob

(6.4).

Swivel saw to a 90° position and set to medium

cutting depth.

- Lock on/off switch

(9.1)

the portable circular

saw in the

ON position with the switch clamp

(9.2).

Suspend chain

switch clamp

the bore

(9.3).

The portable circular saw can be removed

reverse

order.

5.4

Fitting

the

protective

cover

support

Belare inserting the work module or the trim saw

module into the "Basis

Plus" base, the riving knife

the portable circular saw must be replaced

the

protective cover support

(1.3)

(on

delivery

lor

Basis-

Set

"Basis 1

and "Pallas 50" the protective cover

support

ready mounted):

- Adjust cutting depth

saw

that the bolt (10.2)

lor the riving knile lock

visible in the opening of

the guard

the circular

saw.

- Unscrew bolt (10.2) and remove riving knife.

keep the riving knile handy it can be bol ted to the

thread (3.1)

the "Basis Plus" base with the bolt

(1.2).

- Insert protective cover support, position

3-5

lrom the saw blade and lasten with the

bolt (10.2).

Warning:

Tighten bolt lirmly!

The protective cover support has the same lunction

the riving knife. Warning: II the machine is once

again used as a portable circular saw its riving knile

must be re-litted.

5.5

Inserting

the

working

module

trim

saw

module

into

the

"Basis

Plus"

base

unit

- Turn the two countersunk screws

(11.3)

anti-

clockwise so that the screw slot

in the direction

sawing.

- Lock connecting rod in rear position.

- Insert guide unit as shown

Figure

11.

Hold the

guide by the pulling handle

and

the groove

(11.2).

Make sure that the connecting

rod

fits into

the groove

(11.5)

the frame.

- Lock guide unit

rotating both countersunk

screws

(11.3)

in a clockwise direction

90°.

- Screw

bolt

(11.4)

until it rests against

the

trans-

verse section. This prevents the guide plate lrom

sagging.

5.6

Fitting

the

protective

cover

- Unscrew rotary knob (12.2).

Place protective cover on protective cover sup-

port

(12.1)

and tighten with rotary knob

the

bore

(11.1

6 Electrical

connections

and

starting

Warning: The mains voltage must

identical

that

specilied

the portable circular saw's ratings plate.

Plug the portable circular saw's connecting cable

into the socket (2.4)

the Basis Plus. Plug the con-

necting cable Irom the Basis Plus (2.3) into the

mains.

The push switch has a green button (4.6)

and

red

button (4.5) =

OFF.

The push switch has a

neutral circuit breaker to ensure that the saw does

not restart after

apower

lailure until the

button is

pressed.

A switch guard

(eS

70 SA)

(13.1)

can

litted to the

switch casing

prevent the device

from

being switch·

on without authorisation. The switch cover can

be secured with a padlock.

Adjusting

the

saw

Warning: adjustments to the saw may only

car-

ried out when the tool is switched off and the saw

blade

at a standstill!

Lock the connecting

rod

the front position when

adjusting the

saw.

7.1

Cutting

depth

The saw's cutting depth is adjusted with the crank

handle (14.4) The set cutting depth can be

measu-

red

at the saw blade. Recommended setting: cutting

depth

workpiece thickness + 2

5 mm.

7.2 Bevel

cuts

Release the rotary knob

(14.1)

and set the desired

angle with the adjusting wheel (14.3)

swivel the

saw blade. The angle can be read off on the scale

(14.2) on the left edge

the indicator (14.5).

7.3

Adjusting

the

swivel

device

The swivel device is adjusted

the works. Read·

justment is however possible with the two Allen

screws

(5.1,

10.1)

on the side.

7.4

Adjusting

the

drawgear

The support

lor

the portable circular saw

set

the

works

that it is parallel to the drawgear. However,

can

correct with the two screws (10.3).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool PALLAS50 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info