Bedienungsanleitung Festool PALLAS50 (Seite 13 von 59) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

574995

Zoom out

Zoom in

Vorherige Seite

1/59

Nächste Seite

7.5

Adjusting

the

ruler

Open the screws

(15.1,

15.2) to adjust the two rulers

(Order No.

489679,

available from 08/99)

that

the

O-point

the scales

exactiy

with the

cutting line

(15.3).

8 Use

trim

saw

(cross

cuts)

The drawgear

released by a slight pressure from

above on

the

handle (4.1). The saw can now be pul-

led forwards with one hand whilst the workpiece is

lifted with the other hand. Always place the work-

piece against a stop (see Chapter

10)

used

trim saw the protective cover must always be fitted

that the saw blade

always covered. The protec-

tive cover should hereby

lowered onto the work-

piece.

Concealed cuts, e.g. notches or grooves (Fig.

16)

are exceptions which are carried out without the pro-

tective

cover.

For the portable circular saw's original

riving knife

place of the protective cover for con-

cealed cuts. The protective cover must be replaced

immediatelyon completion of such work.

9 Use as a

bench

saw

(longitudinal

cuts)

Lock connecting

rod

in rear position. The saw is now

position for use as a bench (Fig. 17). The work-

piece must

guided along a longitudinal stop (see

section

10.3) during longitudinal cuts.

Limit

stop

system

A correctly set limit stop is

important precondition

for safe working with the saw. The versatile "Basis

WRA

500" mitre fence can be used as a transverse

stop, longitudinal stop or stop for

bevelled cuts. War-

ning: make sure that

all rotary knobs on the mire

fence are tight before starting work.

The "Basis WRA

500" mire lence can be mounted

all

lour

sides of the saw table

shown in illustra-

tion

18.

is ciamped in

ace with the two rotary

knobs

(18.2).

The complete angle unit can

moved

a cros-

swise direction after releasing the rotary knob

(18.1).

10.1

Moving

the

mitre

fence

After the rotary knob (19.3) has been released the

mitre fence

(19.4) can be shifted along the angle unit

and optionally ciamped with a higher (Fig.

19) or

lower guide surlace (Fig.

17). Adjust the mitre fence

for cross and longitudinal cuts so that the max. gap

to the saw blade is

10 mm.

10,2

Angular

adjustment

for bevelied

cuts

After releasing the rotary knob (19.2) and pulling out

the locking pin

(19.1) any angle can be set between

-90°

and +90°. The locking pin can be notched

place for common angle settings.

10.3

Longitudinal

stop

Fitthe mire fence

shown

Fig. 17 for longitudinal

cuts. Alternatively, the "Basis

650" longitudinal

stop

(20.1, Order No.

489675),

available as

extra, can also

used. Make sure that the gap bet-

ween the stop rai! and saw blade does not diminish

towards the back. Otherwise there is a risk that that

cut. -oft parts of the workpiece may become jammed

between the saw blade and stop rai!.

Set the stop

rail

the lower setting and use

the

enclosed guide handle (17.1) when sawing workpie·

ces narrower than 120 mm.

Chan

ging

the

saw

blade

Always wear safety gloves when chan ging saw bla·

des (risk

injury

teeth) Remove the portable

saw circular

change the saw blade (see section

5). The further steps are described

the operating

instructions for the portable circular saw

Connection

dust

extractor

The optional dust extractor set (Order No.

488292)

allows you

connect the "Basis 1

A",

"Palias 50"

Basis·Set

a Festool dust extractor. The dust

extractor set permits the simultaneous extraction

dusts and chips from the portable circular saw

mm) and upper protective cover

mm).

Maintenance and

service

Warning: Always disconnect the mains plug

from

the

socket before carrying out any maintenance work.

Keep the ventilation slots in the motor housing clean

and free of obstructions at

all times to ensure

adequate circulation of

air.

The device

fitted with special motor brushes with

automatie cut-out. When the brushes become

worn the power supply is shut oft automatically and

the tool comes to astandstill.

Any maintenance and repair work requiring

ope-

ning

the motor housing may only be carried out

authorised custorner service workshop.

Accessorles

Festool ofters a wide range

accessories for

the

"Basis

1A:',

"Pallas 50" Basis-Set,

g. trimming

attaehment, sliding table, extension table, dust

extractor set, ete

More details can be lound

the

Festool catalogue.

15 Warranty

Our equipment

under warranty for at least

months with regard to material or production faults

aceordance with national legislation.

the

countries, the warranty period is 24 months

(an

involce or delivery note

required as proof of pur·

chase).

Damage resulting from,

partieular, normal wear

and tear, overloading, irnproper handling, or eaused

by the user or other damage caused

not lollowing

the operating Instruetlons, or any lault acknowled-

ged at the time

purchase, Is not covered

the

warranty.

Complalnts

will only be acknowledged if the equip-

ment has not been dlsmantled before being sent

back to the suppliers or to an authorised Festool

customer support workshop. Store the operating

Instructlons, safety notes, spare parts list and proof

purchase

a sale place.

addition, the manu-

facturer's current warranty condltlons apply.

Note

reserve the rlght to make changes to the technl-

cal data eontalned

thls information

a result of

ongolng research and development work.

Festool PALLAS50 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info