Bedienungsanleitung Festool RO 90 DX FEQ ROTEX (Seite 13 von 83) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

498080

Zoom out

Zoom in

Vorherige Seite

1/83

Nächste Seite

ROTEX

– Install an upstream residual-current cir-

cuit-breaker (FIG, PRCD).

– Connect the machine to a suitable dust ex-

tractor.

– Regularly remove dust deposits in the mo-

tor housing.

5.4 Emission levels

Levels determined in accordance with EN

60745 are typically:

Vibration emission value a

(vector sum for

three directions) and uncertainty K mea-

sured in accordance with EN 60745:

The specified emissions values (vibration,

noise)

– are used to compare machines.

– They are also used for making preliminary

estimates regarding vibration and noise

loads during operation.

– They represent the primary applications of

the power tool.

Increase possible for other applications, with

other insertion tools or if not maintained ad-

equately. Take note of idling and downtimes

of machine!

6 Operation

Connecting and detaching the mains power

cable

[1-4]

see Fig.

[2]

The switch

[1-3]

is an on/off switch (I = ON,

0 = OFF).

The circuit closer can only be actuated if

the change-over switch

[1-2]

is in an en-

gaged position.

In case of a power failure or if the mains

connector is removed, move the on/off

switch immediately to the Off position.

This prevents uncontrolled restarting.

7 Settings

7.1 Electronics

The machine features full-wave electronics

with the following features:

Smooth start-up

The electronically controlled smooth start-up

ensures that the machine starts up jolt-free.

Speed control

You can regulate the speed steplessly with

the adjusting wheel

[1-6]

in the speed range

(see Technical data). This enables you to op-

timise the cutting speed to suit the surface

(see table).

Constant speed

The preselected motor speed remains con-

stant through electronic control to ensure a

uniform cutting speed even when under load.

Wear protective goggles.

Sound pressure level L

= 81 dB(A)

Noise level L

= 92 dB(A)

Measuring uncertainty

allowance

K = 3 dB

CAUTION

Operating noise

Damage to hearing

Use ear protection!

Fine sanding

with W-HT.

= 5,0 m/s²

Uncertainty K = 2,0 m/s²

Coarse sanding

= 5,0 m/s²

Uncertainty K = 2,0 m/s²

Triangular sanding

= 5,0 m/s²

Uncertainty K = 2,0 m/s²

Polishing

= 5,0 m/s²

Uncertainty K = 2,0 m/s²

WARNING

Unauthorised voltage or frequency!

Risk of accident

The mains voltage and the frequency of

the power source must correspond with

the specifications on the machine's name

plate.

In North America, only Festool machines

with the voltage specifications 120 V/60

Hz may be used.

WARNING

Risk of injury, electric shock

Always pull the plug out of the socket be-

fore performing any type of work on the

machine!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool RO 90 DX FEQ ROTEX Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info