Bedienungsanleitung Festool RO 90 DX FEQ ROTEX (Seite 14 von 83) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

498080

Zoom out

Zoom in

Vorherige Seite

1/83

Nächste Seite

ROTEX

Temperature cut-out

The machine power supply is limited and the

speed reduced if the motor exceeds a certain

temperature. The machine continues operat-

ing at reduced power to allow the ventilator

to cool the motor quickly. If the machine

temperature exceeds the maximum permit-

ted value for longer periods, the machine

switches off completely after approx. 40 sec-

onds and can only be switched on again once

the motor has cooled sufficiently.

7.2 Setting sanding motion [3]

The change-over switch

[1-2]

can be used

to set three different sanding motions.

This change-over can only be carried out

with the sanding pad stationary because

the switch is locked during operation.

Coarse sanding, polishing - ROTEX rota-

ry motion

The Rotex rotary motion is a combi-

nation of rotary and eccentric mo-

tions. This position is selected for

sanding with high output (coarse

sanding) and polishing.

Fine sanding - eccentric motion

This position is selected for sanding

with low output for a scratch-free

surface (fine sanding).

Triangular sanding and pad change [4]

This position is used for sanding

with the delta sanding pad and slat

sanding pad; the rotary motion is

blocked.

You can change the sanding pad in

this position.

The stop rod

[1-8]

blocks the in-

stallation of the sanding pad in the

change-over switch positions ROTEX rota-

ry motion and eccentric motion.

7.3 Changing sanding/polishing pad

[5]

Only use sanding and polishing pads that

are suitable for the maximum speed spec-

ified.

Tuned to the surface being processed, the

machine can be equipped with two sanding

pads of different hardnesses.

Hard:

Coarse and fine sanding on surfaces.

Sanding edges.

Soft:

Universal for coarse and fine sanding,

for flat and convex surfaces.

When the interface pad

[1-12]

is fitted on

the sanding pad, strength is reduced = extra

soft.

Following the sanding pad change, switch

the change-over switch

[1-2]

to the de-

sired sanding motion.

7.4 Changing sanding pad [6]

The delta sanding pad DSS-GE-STF-RO90

can be used for sanding close to borders, in

corners or on edges. The slat sanding pad

LSS-STF-RO90 can be used for sanding in

narrow gaps, e.g. louvres.

Observe the following instructions:

Work in corners and on edges tends to sub-

ject the tip to increased stress and results in

increased heat development. In such cases,

work with reduced contact pressure.

Delta sanding pad DSS-GE-STF-RO90

[7]

If the front tip of the StickFix pad

[7-1]

your delta sanding pad is worn, take it off

and turn it 120°.

Slat sanding pad LSS-STF-RO90 [8]

If the StickFix coating of the slat sanding pad

is worn, the complete table can be replaced.

Open the screws to do this

[8-1]

7.5 Attaching sanding accessories

The suitable StickFix sandpaper and StickFix

sanding cloth can be attached quickly and

simply to the StickFix sanding pad.

Press the self-adhesive sanding accessory

onto the sanding pad

[1-7]

7.6 Attaching polishing accessories

To prevent damage, PoliStick accessories

(polishing sponges, polishing felt, sheepskin)

must only be used on the special polishing

pad.

Press the self-adhesive polishing accesso-

ry onto the sanding pad

[1-9]

7.7 Dust extraction

WARNING

Dust hazard

Dust can be hazardous to health. Always

work with a dust extractor.

Always read applicable national regula-

tions before extracting hazardous dust.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool RO 90 DX FEQ ROTEX Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info