Bedienungsanleitung Festool ts 75 ebq fs (Seite 17 von 94) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch)

383463

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

into the hole [3-2] on the cutting depth stop. By

turning the grub screw, the cutting depth can be

set even more exactly (± 0.1 mm).

4.3 Cutting angle

The sawing unit can be swivelled between 0° and

47°:

- Loosen rotary knobs [3-4, 3-6],

- Swivel sawing unit to the desired cutting angle

[3-5],

- Retighten rotary knobs.

Note: both limit positions are set ex works at 0°

and 45°. By turning both setscrews [3-7] counter-

clockwise, the 45° limit position can be increased

to a maximum of 47°.

4.4 Changing the saw blade

- Move lever [4-2] as far as it will go,

- Push switch lock [4-1] up and push sawing unit

down until it locks into place,

- Loosen screw [4-4] with Allen key [4-3],

- Remove saw blade,

- Clean ﬂ ange [4-8, 4-10],

- Insert new saw blade.

The direction of rotation of the saw blade

[4-9] and the machine [4-7] must be the

same.

- Insert outer ﬂ ange [4-10] such that the locking

pins engage into the notches on the inner ﬂ ange

[4-8].

- Tighten screw [4-4],

- Put lever [4-2] back.

4.5 Setting the spacer wedge

- Move lever [4-2] as far as it will go,

- Push switch lock [4-1] up and push sawing unit

down until it locks into place,

- Loosen screw [4-6] with Allen key [4-3],

- Set spacer wedge as shown in diagram 4,

- Tighten screw [4-6],

- Put lever [4-2] back.

4.6 Dust extraction

Always connect the machine to a dust extractor. A

Festool dust extractor with an extractor hose di-

ameter of 36 mm or 27 mm (36 mm recommended

due to the reduced risk of clogging) can be con-

nected to the rotating extractor connector [6-1].

4.7 Mounting the splinterguard

The splinterguard (accessories) signiﬁ cantly im-

proves the quality of the cutting edge of the sawn

workpiece on the upper side for 0° cuts.

- Attach splinterguard [5-1] onto the protective

cover,

- Place machine onto the workpiece or the guide

rail,

- Press splinterguard down until it sits on the

workpiece and tighten it with the rotary knob

[5-2].

- Saw splinterguard in (machine to maximum

cutting depth and speed range 6)

5 Working with the machine

Always secure the workpiece in such a

manner that it cannot move while being

sawed.

The machine must always be held with

both hands by the designated handles

[1-1, 1-6].

Always push the machine forwards [1-2],

never pull the machine backwards to-

wards you.

Adapt the fast-feed speed to prevent the

cutters on the saw blade from overheat-

ing and prevent plastic materials from

melting during cutting.

5.1 Sawing along a scribe mark

The cutting indicator [6-3] displays the cutting line

for 0° and 45° cuts (without guide rail).

5.2 Sawing sections

Place the machine with the front part of the saw

table on the workpiece, switch the machine on,

press it down onto the set cutting depth and push

it forward in the cutting direction.

5.3 Sawing cut outs (plunge cuts)

In order to avoid kickbacks, the following instruc-

tions absolutely must be observed when plunge

cutting:

- The machine must always be placed with the

rear edge of the saw table against a ﬁ xed stop.

When working with the guide rail, the tool must

be placed at the kickback stop [7-1], which is

ﬁ rmly clamped on the guard rail (see Fig. 7;

when not in use, the kickback stop can be kept

in safekeeping at the guide plate [7-2] of the

machine).

- The machine must always be held securely with

both hands and only plunged slowly.

Procedure

place the machine onto the workpiece and posi-

tion it against a stop (kickback stop), switch the

machine on, slowly press it down onto the set

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool ts 75 ebq fs Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info