Bedienungsanleitung Festool ts 75 ebq fs (Seite 16 von 94) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch)

383463

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

2.3 Noise and vibration information

Typical values established in compliance with EN

60745:

Sound-pressure level 95 dB(A)

Sound-power level 106 dB(A)

Measuring uncertainty allowance K = 3 dB

Wear ear protection.

Overall vibration levels (vector sum for three

directions) measured in accordance with EN

60745:

Vibration emission level (3 directions)

Sawing wood a

< 2,5 m/s²

Sawing metal a

< 2,5 m/s²

Uncertainty K = 1,5 m/s²

The emission values speciﬁ ed (vibration, noise)

were measured in accordance with the test con-

ditions stipulated in EN 60745 and are intended

for machine comparisons. They are also used for

making preliminary estimates regarding vibration

and noise loads during operation.

The emission values speciﬁ ed refer to the main

applications for which the power tool is used. If

the electric power tool is used for other applica-

tions, with other tools or is not maintained suf-

ﬁ ciently prior to operation, however, the vibration

and noise load may be higher when the tool is

used. Take into account any machine idling times

and downtimes to estimate these values more

accurately for a speciﬁ ed time period. This may

signiﬁ cantly reduce the load during the machine

operating period.

3 Power supply and start-up

The mains voltage must correspond to

the speciﬁ cation on the rating plate.

Always switch the machine off before

connecting or disconnecting the mains

lead!

See Fig. 2 for connection and disconnection of the

power cable. The switch [1-7] is for switching on/

off (push = ON, release = OFF).

The switch can only be activated after the switch

lock [1-8] has been pushed up. Activating the

switch lock simultaneously locks the plunging

equipment and the sawing unit can be moved

down against the spring force. This causes the

saw blade to emerge from the protective cover.

When the machine is lifted, the sawing unit

springs back into the starting position.

Only guide the machine against the work-

piece when it is switched on.

Check the installation ﬁ xture prior to use

and do not use the machine if the ﬁ xture

does not function correctly.

4 Machine settings

Always pull the plug out of the socket

before making settings.

4.1 Electronics

The TS 75 EBQ/ TS 75 EQ features full-

wave electronics with the following prop-

erties:

Smooth start-up

The smooth start-up ensures the machine starts

up jolt-free.

Speed adjustment

You can regulate the speed steplessly between

1350 and 3550 min

-1

using the adjusting wheel

[1-5]. This enables you to optimise the cutting

speed to suit the material (see table 1).

Constant speed

The preselected speed remains constant whether

the machine is in operation or in neutral posi-

tion.

Temperature cut-out

To prevent overheating, the safety electronics

switches the machine off when it reaches a critical

motor temperature. Let the machine cool down

for approx. 3-5 minutes before using it again. The

machine requires less time to cool down if it is

running, i.e. in neutral position.

Current limiting

Current limiting prevents permissibly high current

consumption under extreme overload. This can

lead to a decrease in the motor speed. The motor

immediately restarts after the load is removed.

Brake (TS 75 EBQ)

After switching-off the tool, the saw blade is

electronically brought to a standstill in 1.5 – 2

seconds.

4.2 Cutting depth

The cutting depth can be set at 0 – 75 mm:

- Press the cutting depth stop [3-3] and move it to

the desired cutting depth (the values speciﬁ ed

on the scale [3-1] apply to 0° cuts without guide

rail),

- Release the cutting depth stop (the cutting depth

stop notches along in 1 mm-steps).

The sawing unit can now be pressed down to the

set cutting depth.

A grub screw (M4x8 to M4x12) can be screwed

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool ts 75 ebq fs Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info