Bedienungsanleitung Flex ske 2902 vv (Seite 9 von 102) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

383715

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

OPERATING INSTRUCTIONS

FOREWORD

The FLEX SKE 2902 VV is designed for cutting wood up to 30.5 cm thick, metal up to 19 mm thick and

various other materials, such as plastics, fiberglass, hard rubber, etc.

TO START AND STOP SAW

1. Make sure power circuit voltage is the same as shown on the specification plate on the saw.

Connect saw to power circuit.

2. Hold saw firmly. Squeeze trigger switch (A) Fig. 1, to start motor. Release trigger to stop motor.

VARIABLE SPEED

The saw is equipped with a variable speed control (0 to 2600 SPM). As the switch trigger is squeezed, the

speed of the saw blade increases.

The lower speeds are recommended for most metal cutting, while the higher speeds are recommended

for wood. A few practice cuts at various speeds (on scrap material), will aid you in choosing the best speed

for obtaining the desired results on your application.

HOW TO HOLD SAW

Hold saw as shown in Fig. 2. The gear housing, intermediate plate, blade and pivoting guide shoe may be

made live if the blade cuts into live wiring within a wall.

TO PREVENT ACCIDENTAL ELECTRICAL SHOCK THE SAW MUST BE

HELD AS SHOWN IN FIG. 2, AND MUST HAVE THE RUBBER FRONT

HOUSING COVER PROPERLY INSTALLED AND NOT DAMAGED.

SELECTING THE BLADE

For best performance, longer blade life, and smoother cut, select the proper blade for the job.

When cutting metal always select a blade which will allow at least three teeth to be engaged in the

thickness of material.

INSTALLING THE BLADE

Model SKE 2902 VV with Quik-Change™ Blade Clamp

1. The reciprocating shaft must be fully extended to permit access to the Quik-Change™ blade release

collar (A) Fig. 4. If necessary, gently squeeze the trigger switch to move the reciprocating shaft to its

outermost position (as shown in Fig. 4).

DISCONNECT TOOL FROM POWER SOURCE.

2. Pivot the guide shoe (B) Fig. 4, forward to improve access to the blade clamp.

3. To open the blade clamp: rotate and hold the blade release collar (A) Fig. 5, counterclockwise (as

viewed from the front of the saw).

4. Insert the blade into the clamp until it bottoms. Allow the release collar to rotate clockwise to lock the

blade in place (Fig. 6).

5. To remove blade: repeat steps 1 thru 3, and pull blade from blade clamp (while the release collar is

being held in the open position).

NEVER TOUCH BLADE IMMEDIATELY AFTER USE, AS IT MAY BE

EXTREMELY HOT.

NOTES: If the blade clamp collar resists rotation to remove a blade, work the blade up and down

while rotating the clamp (in a counterclockwise direction).

If the blade breaks leaving nothing to grasp (to pull it from the clamp), it may be necessary to use

another blade as a tool to aid in removing the broken piece (see Fig. 7). While holding the release

collar in the open position, use the tip of another blade to "hook" the broken piece and pull it from

the clamp. (A thin, fine-toothed, metal-cutting blade works best.)

WARNING

SKD.book Seite 9 Dienstag, 29. August 2006 8:42 20

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Flex ske 2902 vv Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info