Bedienungsanleitung Flex ske 2902 vv (Seite 11 von 102) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

383715

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

Clearly mark line of cut on the work. Set saw for orbital motion to get the best plunge cut per-for mance.

Grasp front housing with one hand and rear handle with the other hand. To start cut, rest saw on shoe

bracket, align blade with the marked line of cut, (blade NOT touching work),as shown in Fig. 13. Start saw.

Using bracket as a pivot point, roll saw forward by raising rearhandle, as shown in Fig. 14. When blade

has cut through the work, continue raising the rearhandle until saw is perpendicular to the work surface.

Keep saw in this position and move blade along line of cut.

SAWING METAL

When cutting angle, H-beam, I-beam, channel, etc., start the cut on the surface where the greatest number

of teeth will contact the work. To make a pocket cut, drill a starting hole first. To extend blade life, cutting

oil can be applied to the work surface along the line of the cut.

MAINTENANCE

KEEP TOOL CLEAN

Periodically blow out all air passages with dry, compressed air. All plastic parts shouldbe cleaned with soft

damp cloth. NEVER use solvents to clean plastic parts. They couldpossibly dissolve or otherwise damage

the material.

Wear ANSI Z87.1 safety glasses while using compressed air.

FAILURE TO START

Should your tool fail to start, check to make sure the prongs on the cord plug are makinggood contact in

the outlet. Also, check for blown fuses or open circuit breakers in the line.

BRUSH INSPECTION AND LUBRICATION

For your continued safety and electrical protection, brush inspection and replacement onthis tool should

ONLY be performed by an Authorized Service Agent for FLEX Power Tools.

At approximately 100 hours of use, take or send your tool to your nearest AuthorizedService Agent for

FLEX Power Tools to be thoroughly cleaned and inspected; worn parts replaced, and when necessary;

relubricated with fresh lubricant, if required; reassembled with new brushes; and performance tested.

Any loss of power before the above maintenance check may indicate the need forimmediate servicing of

your tool. DO NOT CONTINUE TO OPERATE TOOL UNDER THIS CONDITION. If proper operating

voltage is present, return your tool to the Service Agent for immediate service.

SERVICE AND REPAIRS

All quality tools will eventually require servicing or replacement of parts due to wear fromnormal use.

These operations, including brush inspection and replacement, should ONLY be performed by an

AUTHORIZED Service Agent for FLEX Power Tools. All repairs made bythese agencies are fully

guaranteed against defective material and workmanship. We cannot guarantee repairs made or attempted

by anyone other than these agencies.

Should you have any questions about your tool, feel free to write us at any time. In anycommunications,

please give all information shown on the nameplate of your tool (modelnumber, type, serial number, etc.).

PROTECTING THE ENVIRONMENT

Only for EU countries. Do not dispose of electric tools together with household wastematerial! In

observance of European Directive 2002/96/EC on waste electrical andelectronic equipment and

its implementation in accordance with national law, electric tools that have reached the end of

their life must be collected separately and returned to an environmentally compatible recycling

facility.

WARNING

SKD.book Seite 11 Dienstag, 29. August 2006 8:42 20

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Flex ske 2902 vv Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info