Bedienungsanleitung Flex ske 2902 vv (Seite 10 von 102) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

383715

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

Periodically clean the blade clamp with dry compressed air. DO NOT lubricate the blade clamp.

Lubricant can attract contamination.

Wear ANSI Z87.1 safety glasses while using compressed air.

DUAL BLADE MOTION

Model SKE 2902 VV has dual blade motion: you have a choice of straight reciprocating motion, as shown

in Fig. 8, or orbital motion as shown in Fig. 9. Straight reciprocating motion should be used for all metal

cutting operations, and for wood cutting applications where finish is more important than speed. Orbital

motion is used for fast cutting of wood.

To set saw for straight reciprocating motion: rotate knob (A) Fig. 8, clockwise so that the bar is vertical

(opposing arrow symbol up), as shown in Fig. 8.

To set saw for orbital motion: rotate knob (A) Fig. 9, counterclockwise so that the bar is horizontal (oval

arrow symbol up), as shown in Fig. 9.

PIVOTING GUIDE SHOE

The pivoting guide shoe (A) Fig. 10 serves as a rest while making a cut and it can be adjusted to

accommodate many types of cutting applications.

DISCONNECT TOOL FROM POWER SOURCE.

DO NOT OPERATE THE SKE 2902 VV WITH THE GUIDE SHOE

REMOVED.

The SKE 2902 VV is supplied with a keyless Quik-Change™ pivoting guide shoe. To adjust, rotate lever

(A) Fig. 11 releasing the pivoting guide shoe (B). Adjust to desired position and close lever (A) Fig. 12.

The keyless Quik-Change™ pivoting guide shoe is designed with a raised lip (C) Fig. 11 at the end that

prevents the guide shoe from locking in position if it is extended out too far. After adjusting, make sure the

locking lever is completely closed in the locked position (A) Fig. 12.

NOTE: DO NOT force the locking lever closed. Adjust shoe enough to allow the lever to lock in

position without force.

USING THE SAW

BEFORE YOU START TO WORK

Select the blade best suited for the material to be cut. For greatest economy, use the shortest blade

suitable for the thickness of the material to be cut.

Be sure the material to be cut is rigid. Small work pieces should be securely clamped in a bench vise or

with clamps to the work table. As the work progresses in scroll or curved cut-out pieces, the material may

be readjusted to accommodate the movement of the saw. If the work is large enough, it may be held only

by hand across saw horses. The saw cuts freely with only slight feed pressure. Forcing the saw will not

make it cut faster.

SAWING WOOD

The SKE 2902 VV is used much the same as a hand saw in that it is moved toward the operator during

the cutting operation. However, since the blade cuts on the up-stroke instead of the down-stroke as in the

case of the hand saw, the good or finish side of the work should face down during the cutting operation.

PLUNGE CUTS

The SKE 2902 VV can be used for plunge cutting wood, plywood, wallboard, and plasticmaterials.

DO NOT attempt to plunge cut metal.

WARNING

SKD.book Seite 10 Dienstag, 29. August 2006 8:42 20

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Flex ske 2902 vv Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info