Bedienungsanleitung Freerider FR510DXXs (Seite 31 von 48) (Englisch)

664131

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

FIG 39

FIG 40

BASIC FAULT FINDING

If your Freerider Scooter will not start:

If the battery condition meter fail to operate when the

key switch is in the 'on' position, check the following:

Freerider

The battery condition indicator meter , your Freerider

does not drive:

1. Check the power key switch is turned fully 'on'. If it is,

the battery condition indicator meter displayed on your

console, will be operating. If the first red status light is

flashing once per second, charge your batteries.

1. Make sure the battery charger is not plugged into the

tiller charge socket, this will prevent drive.

2. Check both battery connectors ( grey connectors ).

Check battery terminal condition ( fig 23, page 21).

3. Check the 'circuit breaker': If your Scooter stops

for no apparent reason, it is probably due to the circuit

breaker disconnecting from the speed control electronic

box (see fig 40). On rare occasions, a temporary

overload on the electric circuit can occur - for instance

when climbing a steep incline. If this happens, the circuit

breaker situated under the rear body cover will trip and

all power to your drive system will be automatically

switched off. Wait for approximately 60 seconds, switch

the circuit breaker to 'on 'by entering a finger through

the access hole in the top of the rear body cover (located

under your seat ) and press the switch down. The battery

gauge will light up and you are now ready to drive again.

If the circuit breaker trips up again wait for 5 minutes and

try again.

If you find the circuit breaker is continually tripping

out, contact your authorised dealer.

1. Check the 'white' plug's, located under the rear

cover and positioned in the main controller module

(see Fig 41).Also check status fault codes (page 32 )

Caution:

If your Freerider Scooter will not start:

the battery condition

meter fail to operate when the

key

switch

is in

the

'on' position,

check

the following:

Freerider

The

battery

condition

indicator

meter

your

reerider

does

not

drive:

Caution:

HANDLE BAR BEARINGS

The bearings which control the movement of the steering

handle bar may need to be adjusted if up and down

movement is noticed in your steering handle bars.

The bearings are accessed by lifting the back rubber cover at

the base of your handle bars and the front body cover.

The bearings are adjusted by first releasing the locking nut

anti-clockwise one full turn with a suitable spanner (fig 39).

Turn the upper bearing adjustment nut clockwise, one flat at

a time until all of the up and down movement in the handle

bars is removed. Retighten the lock nut clockwise into

position with a second spanner. Do not overtighten the

bearing adjustment nut, as this will damage the bearing

tracks.

HANDLE BAR BEARINGS The handle bar bearings are NOT 'Sealed for life' and may

require lubrication with a general purpose bearing grease

on an annual basis.

NOT 'Sealed for life' and may

require

lubrication with a general purpose bearing grease

an annual basis.

FIG 42

motor

brake

charge

output

tiller

console

supply

Battery input

FIG 40

FIG 41

FIG 40

FIG 42

Controller

P&G EGIS 110

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Freerider FR510DXXs Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info