Bedienungsanleitung Futaba 6EXAP (Seite 6 von 24) (Englisch)

28983

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

• After the servos are installed, operate each servo over its full travel and check that the pushrods and servo arms do not bind or

contact each other. Also make sure the controls do not require excess force to operate. If there is an objectionable buzzing

sound coming from a servo, there is probably too much resistance in the control. Find and correct the problem. Even if there is

no servo damage, excess battery drain will result.

• Use the mounting plate

mounting plate

from the receiver on/off switch as a template for the cutout and screw holes. Mount the switch on the

side of the fuselage opposite the engine exhaust, and where it won

’t be inadvertently turned on or off during handling or

storage. Be certain the switch moves without restriction and “snaps” from ON to OFF, and that the cutout allows full motion

full motion

the switch in both

both

directions.

• IMPORTANT: NEVER

IMPORTANT: NEVER

cut the receiver antenna or mount it in the model folded back on itself. Doing so will change its

electrical length, possibly reducing the distance from the pilot that the model can be controlled (“range”).

• The receiver antenna may be mounted inside or outside the model:

Internal antenna mounting:

The antenna may be routed down through the inside of the fuselage, or through any non-metallic

non-metallic

housing or tube within the

fuselage. Keep the antenna away from metal pushrods, wires and cables; otherwise, range may be decreased. Always perform a

range check before flying (see page 22).

External antenna mounting:

A. Use a cut off servo arm as a “stop

stop

” or strain relief

strain relief

inside the fuselage to keep

tension off the solder joint holding the antenna to the receiver. Guide the antenna

through a hole in the fuselage. (If possible, insulate the hole with a rubber grommet or a

small piece of rubber tubing.)

B. Make a hook

hook

from another cut off servo arm. Insert the end of the antenna

through two holes, then connect the hook to a rubber band around a pin inserted into the

vertical stabilizer. Allow any excess antenna length to trail behind the hook.

• The receiver contains precision electronic parts. It is the most delicate (and expensive) radio component on-board the model

and should be protected from vibration, shock and temperature extremes. To protect the receiver, wrap it in R/C foam rubber or

other vibration-absorbing material. If appropriate, waterproof the receiver by placing it in a plastic bag and closing the open

end with a rubber band before wrapping it in foam. If moisture enters the receiver, intermittent operation or a failure may result.

Wrapping the receiver in a plastic bag also protects it from fuel and exhaust residue which, in some models, can work its way

into the fuselage.

Mounting the frequency clip:

(for USA)

• To announce your frequency and avoid potential interference problems, the

frequency number should always be displayed on the transmitter antenna while

flying. Peel the backing from the numbers and apply them to both sides of the

clip. Snap the end of the clip that fits best to the base of the antenna as shown.

You may cut off the other end of the clip.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 6EXAP Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info