Bedienungsanleitung Futaba FP8JN (Seite 8 von 16) (Englisch)

30088

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

• USING THE TRANSMITTER

Before using the transmitter, charge the NiCd

battery.

•Connect the DIN connector of the FBC-2L

charger to the charging jack of the transmitter

and the 3P connector to the receiver servo NiCd

battery (NR-4H), and plug the charger into an

AC110V outlet as shown in Fig. 3. The Tx, Rx

charging indicator LED illuminate to indicate that

the battery is being charged.

•The charging time is normally 15 hours. But if the

battery has not be used for some time, charge it

for about 20 hours.

(If the battery is left in the discharged state for a

long time, its capacity and life will be adversely

affected.)

•The

transmitter and

receiver

NiCd batteries

can

be charged simultaneously, or independently.

•The battery can usually be used about 10 times

at a rate of about 10 minutes/time.

•Extend the antenna.

Pull the

first

stage

of the antenna up and

turn

counterclockwise until it locks as shown in Fig. 4.

•If the antenna is not locked, it will not be con-

nected to the internal circuitry.

•The power switch is a lock type switch. When it

is set to ON while pulling it forward, the level

meter pointer will deflect, indicating the antenna

output. The transmitter is OK if the pointer

deflects to graduation 7 with the antenna ex-

tended fully.

The pointer indication is different when the

antenna is contracted and when it is extended

fully.

[The pointer indication will also be different

when the antenna is grasped with your hand and

when it is not grasped.)

When the antenna is contracted, the transmitter

does not deliver an output even though the level

meter pointer deflects. DO NOT USE THE

TRANSMITTER UNDER THIS STATE.

•Push the battery check switch. The level meter

pointer will indicate the battery voltage at this

time. The battery is OK if the meter pointer de-

flects to within the green zone. If the pointer de-

flects to near the boundary between the green

and red zones, recharge the battery.

•Using the D.S.C. function

The

servos

can

operated

without

transmitting

by connecting the D.S.C. cord furnished with the

set to the connector (Fig. 1 ) of the trans-

(Use this function with the power switch of the

transmitter set to the OFF position. Although

the D.S.C. Function will be operative when the

power switch is set to ON, it will be meaningless.)

•Using dual travel

(DR —aileron, DR —elevator)

When the dual travel switch is set to ON, the

steering angle becomes small (within the range

indicated by the hatched lines in Fig. 5). The

steering angle can be varied from 40% (minimum)

to 100% (maximum) of the total steering angle

by adjusting the trimmer

mitter and the C terminal of the receiver. This

allows adjustment of the aircraft while awaiting

your turn to fly.

on the trimmer panel for channel 8)

next to the switch with a screwdriver. The dual

switch should normally be set to OFF. However

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FP8JN Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info