Bedienungsanleitung Futaba FP8SSHP (Seite 28 von 36) (Englisch)

30098

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

•IDLE UP 2 ADJUSTMENT

1. When the idle up 2 switch [21] is set to ON, the

idle up amount (throttle servo stop position) can

be adjusted with trimmer [10] of the throttle trim-

mers [C] on the trimmer panel at the back of the

transmitter. The low side pitch can be adjusted

with trimmer [6] of the pitch trimmers [B] on the

trimmer panel on the back of the transmitter.

2 When trimmer [10] is

turned clockwise, idle up is

applied. (See Fig. 61.)

3 Set the idle up 2

point trimmer [11] for dynamic

patterns.

4 Adjust the low side pitch to match rolls and other

dynamic pattern with trimmer [6].

When trimmer [6] is

turned clockwise and

switch

[21]

is in the ON

position, the pitch

increases at the minus

side.

Pitch control servo

Fig.

4. Adjust trimmer [8] so the engine stops (throttle

fully closed) when entering auto-rotation and when

switch

[23]

is in the ON position and idles (throttle

slightly open) during practice.

5 Adjust the maximum pitch when switch

[23] is set

ON with the ATV button.

The pitch servo moves to the

position set at the

ATV button without regard to the

position of the

pitch control high side trim lever

[13].

6 Throttle hold delay adjustment

Set the hold delay trimmer [7]

full counterclock-

wise

to the 0 position.

• Next, perform auto-rotation. When the drop is

fast the instant throttle hold is applied, turn the

hold delay trimmer [7] and set it for a constant

drop.

•Set

the

hold

delay

trimmer [7]

the

minimum

required time. Normally, about 0.7 second. This

is about 30% to 40% by trimmer position.

7 When performing auto-rotation using hold delay,

set the throttle lever to maximum slow, then im-

mediately turn on throttle hold switch

[23].

• If you are not familiar with auto-rotation, use

the set with the hold delay trimmer [7] turned

fully counterclockwise to 0 hold delay.

• Rudder button adjustments

1 When the rudder button [33] is pressed, the rudder

servo moves in the direction and to the angle

set

trimmer [17] of the rudder trimmers

[D] on the

trimmer panel at the back of the transmitter.

2. The time the rudder is operated can be set with

the

rudder time trimmer [18] on the trimmer panel at

the back of the transmitter.

3 Set

the rudder

servo

throw

the

direction and

angle matched to 540* for stall turns and other

spinning maneuvers.

•Throttle hold and throttle hold delay

adjustment for auto-rotation

1. When the throttle hold switch [23] is set to ON, the

throttle circuit is disconnected from the throttle

lever and only pitch control can be performed with

the lever.

2. The auto-rotation pitch can be adjusted with trim-

mer [5] of the pitch trimmers [B] and the auto-

rotation throttle servo stop position can be adjust-

ed with trimmer [8] of the throttle trimmers

[C]

on the trimmer panel at the back of the trans-

mitter.

3. Adjust trimmer [5] for a pitch of about minus 2

when switch [23] is ON and the throttle lever is in

the maximum position. (This pitch differs some-

what with the helicopter.)

[Fail safe switches]

After you have become completely familiar with your

set, set switches 12, 13, 14, 19 and C on the trimmer

panel at the back of the transmitter to the ON posi-

tion. When first using your set, practice with the

switches in the OFF (INHIB) position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FP8SSHP Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info