Bedienungsanleitung Futaba T-18MZ-WC (Seite 43 von 178) (Englisch)

747919

Zoom out

Zoom in

Vorherige Seite

1/178

Nächste Seite

＜

Model Basic Setting Procedure

＞

Operation of the swash plate near the hovering point

FDQEHFRUUHFWHGE\VZDVK$)5IXQFWLRQFRUUHFWLRQ

PL[LQJ8VHWKLVZKHQSLWFKDLOHURQDQGHOHYDWRU

operation causes the swash plate to deviate from

the normal direction.

&DOOWKH6ZDVKVHWXSĺ6ZDVKGHWDLOVVFUHHQ

Pitch slow side and high side linkage correction is also

SRVVLEOH$GMXVWVRWKDWSLWFKRSHUDWLRQFDXVHVWKH

swash plate to move up and down in the horizontal

state.

5. Throttle curve setting

This function adjusts the pitch operation curve

in relation to the movement of the throttle stick for

each condition.

(17 points curve)

The pitch curve can be freely selected from linear

operation curve to smooth curve, and adjusted to

match the curve you want by means of the T18MZ-

WC’s powerful Curve Edit Function (6 types of

curves can be selected). Up to 17 points can be set

for linear or curve types. However, when using the

3 points or 5 points specified to create a curve, a

simple and smooth curve can be created by selecting

the curve type and reducing the number of input

SRLQWVWRRUDQGWKHQHQWHULQJWKHVSHFL¿HGYDOXH

at the corresponding points that you created.

6HWWLQJH[DPSOH!

Call the throttle curve of each condition with the

condition select switch.

ŏ1RUPDOFXUYHDGMXVWPHQW

Normal curve uses Normal (Linear) type and creates

a basic pitch curve centered near hovering. This

curve is adjusted together with the Throttle Curve

(Normal) so that the engine speed is constant and

up/down control is easiest.

ŏ,GOHXSFXUYHDGMXVWPHQW

The high side pitch curve sets the maximum pitch

regardless of the engine load. The low side pitch

curve creates a curve matched for aerobatics (loop,

roll, 3D, etc.).

Note: When the curve type is changed, the data is

reset.

ŏ7KURWWOHKROGFXUYHDGMXVWPHQW

4. Fuselage linkage

Connect the throttle rudder, ailerons, elevators,

pitch, and other rudder linkages in accordance with

the kit instruction manual. For a description of

the connection method, see "Receiver and servos

connection".

*The channel assignment of the T18MZ-WC is different from

that of our existing systems. (The channel assigned to each

function can be checked at the function menu of the Linkage

Menu.)

ŏ:KHQWKHGLUHFWLRQRIWKHOLQNDJHLVUHYHUVHG

use the Reverse function of the Linkage Menu.

$OVRXVHWKHVZDVK$)5IXQFWLRQLQDQ\VZDVK

set up other than the H-1 mode.

ŏ$GMXVWWKHGLUHFWLRQRIRSHUDWLRQRIWKHJ\UR

(Gyro side function)

ŏ&RQQHFWWKHWKURWWOHOLQNDJHVRLWLVIXOO\FORVHG

with the trim setting all the way down.

ŏ$GMXVWWKHQHXWUDOSRVLWLRQDQGUXGGHUDQJOH

DWWKHOLQNDJHVLGHDQGÀQHWXQHZLWKWKH6XE

Trim function and End Point function (rudder

angle adjustment). To protect the linkage, a

limit position can also be set with the End Point

function.

ŏ6ZDVKSODWHFRUUHFWLRQ([FHSW+PRGH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba T-18MZ-WC Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info