Bedienungsanleitung Futaba T-18MZ-WC (Seite 44 von 178) (Englisch)

747919

Zoom out

Zoom in

Vorherige Seite

1/178

Nächste Seite

＜

Model Basic Setting Procedure

＞

&RQÀUPWKDWWKHUDWHRIWKHVORZHVWSRVLWLRQRI

WKHVWLFNLVLQLWLDOVHWWLQJ

%HVXUHWKDWZKHQVHWWRKLJKVLGHWKHFXUYHRI

DQ\FRQGLWLRQGRHVQRWH[FHHG

Example of pitch curve setting:

1. Call the pitch curve of each condition with

the condition select switch.

*Pitch curve graph display can be switched to pitch angle direct

reading display.

$3LWFKFXUYH1RUPDO

Make the pitch at hovering approximately +5

Set the pitch at hovering with the stick position at

WKHSRLQWDVWKHVWDQGDUG

*Stability at hovering may be connected to the throttle curve.

Adjustment is easy by using the hovering throttle function and

hovering pitch function together.

%3LWFKFXUYH,GOHXS

The idle up 1 pitch curve function creates a curve

PDWFKHGWRDLUERUQHÁLJKW

Set to -7

a

as standard.

&3LWFKFXUYH,GOHXS

The high side pitch setting is less than idle up 1.

The standard is +8

D. Pitch curve (Hold)

$WDXWRURWDWLRQXVHWKHPD[LPXPSLWFKDWERWK

the high and low sides.

[Pitch angle setting example]

7KURWWOHKROG

a

6. Throttle hold setting

Call the Throttle Hold function from the Model

Menu and switch to the throttle hold condition with

the condition select switch.

Note: $WLQLWLDOVHWWLQJWKHVHWWLQJPRGHLVWKH

group mode. Since this function is not used at other

conditions, switch to the single mode before setting.

ŏ6HWWLQJWRWKHVWDWHZKLFKDFWLYDWHVWKHIXQFWLRQ

The throttle hold function allows setting for throttle cut

DQGVZLWFKLQJRIWKHIXQFWLRQÀ[HGDWWKHLGOHSRVLWLRQ

by switch for training. Either one or both functions

can be performed.

ŏ+ROGSRVLWLRQVHWWLQJ

This function sets the servo operation position at

throttle hold. (Throttle cut and idle positions)

ŏ2WKHUVHWWLQJV

When you want to link operation with stick

PDQLSXODWLRQWKH$XWRPRGHFDQEHVHW

When you want to adjust the servo speed, adjust

[Speed].

3LWFKWR58'PL[LQJVHWWLQJ

Use this function when you want to suppress

the torque generated by the changes in the pitch

and speed of the main rotor during pitch operation.

Adjust it so that the nose does not swing in the

rudder direction. However, when using a heading

hold gyro like those shown below, do not use Pitch

to RUD mixing.

Note:KHQXVLQJD)XWDED*<VHULHVJ\URRURWKHU

KHDGLQJKROGJ\URWKLV3LWFKWR58'PL[LQJVKRXOG

not be used. The reaction torque is corrected at

WKHJ\URVLGH:KHQRSHUDWLQJWKHJ\URLQWKH$9&6

mode, the mixed signal will cause neutral deviation

symptoms and the gyro will not operate normally.

Call the Pitch to RUD mixing function from the

Model Menu, and set the curve for each condition.

(At initial setting, this function is in the "INH" state.

To use it, set it to the "ON" state.)

(17 points curve)

Curve setting of up to 17 points is possible.

However, in the following setting example, a simple

curve can be adjusted by using the [Linear] curve

type.

Note:$WLQLWLDOVHWWLQJWKHVHWWLQJPRGHLVWKHJURXS

PRGH,QWKLVPRGHWKHVDPHFRQWHQWVDUHVHWDWLQ

all conditions. When you want to set the selected

condition only, switch to the single mode.

6HWWLQJH[DPSOH!

Call the mixing curve of each condition with the

condition select switch.

The throttle hold curve is used when performing auto

rotation dives.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba T-18MZ-WC Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info