Bedienungsanleitung Gaggenau BSP270111 (Seite 17 von 56) (Englisch)

755787

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

en Operating the appliance

Inserting accessories

The wire rack and the perforated cooking container are

fitted with a locking function. The locking function

prevents the accessories from tilting when they are

pulled out. The accessories must be correctly inserted

into the cooking compartment for the tilt protection to

work properly. To pull out the accessories, lift them

slightly.

When inserting the wire rack, make sure that

▯the lug (a) is facing downwards

▯the safety bar on the wire rack is at the back and

facing upwards.

When inserting the cooking container, ensure that the

lug (a) is facing upwards.

Switching on

1Use the function selector to set the required type of

heating. The selected type of heating and

recommended temperature appear on the display.

2If you wish to change the temperature:

Turn the rotary selector to set the desired

temperature.

The heat-up symbol ’ appears on the display. The bar

shows the current heat-up status. When the set

temperature has been reached, an audible signal

sounds and the heat-up symbol ’ goes out.

Note: The temperature that has been set will be

retained when you change to a different operating

mode. The suggested temperature does not appear until

the appliance has been switched on.

Switching off

Turn the function selector to 0.

Depending on the operating mode, you may hear an

automatic rinse cycle running.

Steam injection

With steam injection, steam is specifically injected into

the cooking compartment. This enables you to bake, e.g.

bread and bread rolls, with sufficient moisture.

Steam injection only works with these types of heating:

▯Hot air + 30% humidity

▯Hot air + 0% humidity

▯Full surface grill + air recirculation

To start steam injection, touch the ð symbol. After a

short while, steam is injected into the cooking

compartment.

Steam is injected for approx. 5minutes.

To cancel steam injection:

Press the ñ symbol.

Steam removal

During the steam removal process, cold water is

introduced into the cooking compartment. This cools

the cooking compartment down and the steam

condenses on the cooking compartment wall. When you

then open the cooking compartment door, only a little

steam escapes.

mWarning – Risk of scalding!

After opening the cooking compartment door, hot water

may drip down from it.

Steam removal only works with the following types of

heating and if the temperature in the cooking

compartment is below 130 °C:

▯Hot air + 100% humidity

▯Hot air + 80% humidity

▯Hot air + 60% humidity

▯Full surface grill Level 1+ humidity

▯Full surface grill Level 2+ humidity

▯Sous-vide cooking

Proceed as follows:

Touch the ¡ symbol. Steam removal takes

approximately 25seconds. During this time, the heating

is switched off.

Stopping steam removal early:

Open the door or touch the ¢ symbol.

Time-setting options en

Notes

– The steam removal function is also available for a

short time after switching off the appliance.

– Steam removal takes place automatically at the end

of an automatic programme or a timer programme

(cooking time).

After every use

1Remove food remnants from the cooking

compartment surfaces as soon as the appliance has

cooled down. Burnt-on remnants will be much

harder to remove later.

2In order to dry the cooking compartment, the

cooling fan and the fan wheel on the back wall of

the cooking compartment continue to run for a

while after the appliance is switched off. They then

switch off automatically. This may take up to

95 minutes. The appliance door must remain closed

while the cooking compartment is being dried.

3If required, you can dry the cooking compartment

quickly using the drying programme. ~ "Drying

programme" on page 36

4Once the cooking compartment has cooled down,

polish it with a soft cloth.

5Wipe units and handles dry where condensation

has formed.

Safety shut-off

For your protection, the appliance is equipped with an

automatic safety shut-off. Any heating process is

switched off after 12 hours if the oven is not operated in

this time. A message appears in the display.

Exception:

The long-term timer has been programmed.

Set the function selector to 0, then the appliance can be

operated again as usual.

Time-setting options

Time-sett ing options

You use the timer menu to make the following settings:

Š Short-term timer

p Stopwatch

6 Cooking time (not in standby mode)

5 Cooking time end (not in standby mode)

Calling up the timer menu

You can call up the timer menu from any mode. Only

from the basic settings, function selector is set to S, the

timer menu is not available.

Touch the M symbol.

The timer menu is displayed.

Timer

The timer runs independently of the other appliance

functions. You can enter a maximum of 90 minutes.

Setting the timer

1Call up timer menu.

The "Timer" Š function is displayed.

2Turn the rotary selector to set the required cooking

time.

3Start with I.

6KRUWWHUPWLPHU



Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gaggenau BSP270111 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gaggenau BSP270111

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info