Bedienungsanleitung Gaggenau CV282 (Seite 30 von 52) (Englisch)

702999

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

en Automatic functions

▯ The cooking sensor function is made available once

the temperature sensor has been connected to the

control panel correctly.

▯ If there is a fault with the temperature sensor, the

connection may not be established correctly for the

following reasons:

– Bluetooth communication error.

– You did not press the ¨ symbol on the

temperature sensor within 30 seconds of

selecting a hotplate.

– The battery in the temperature sensor has run

out.

Reset the wireless temperature sensor and follow

the connection procedure once again.

▯ If the temperature sensor and the control panel are

not connected correctly due to a transmission error,

follow the connection procedure once again.

If no connection can be established, inform the

after-sales service.

Resetting the wireless temperature sensor

1 Touch and hold the ¨ symbol for approximately 8-

10 seconds.

While you are doing this, the temperature sensor's

LED indicator will light up three times. When the

LED lights up for the third time, it will start to reset

the temperature sensor. At this point, you will need

to lift your finger off the symbol.

Once the LED goes out, this means that the

wireless temperature sensor has been reset.

2 Repeat the connection procedure from point 2.

Programming

The hob must be on.

1 Attach the temperature sensor to the cookware, see

section ~ "Preparation and maintenance of the

wireless temperature sensor"

2 Place the cookware with sufficient liquid in the

middle of the desired element and always put a lid

on.

3 Select the required hotplate using the twist knob.

‹ appears in the display for the heat setting.

4 Press the ¨ symbol in the control panel. An audible

signal sounds. The ¨ symbol lights up in the

display for the hotplate.

5 Press the ¨ symbol on the wireless temperature

sensor on the cookware. Once the wireless

temperature sensor has been detected, the default

temperature of 95 °C lights up in the hotplate

display.

6 Set the required temperature using the twist knob.

The temperature can be changed by increments of

5°C.

7 The hotplate display shows the progress of the

heating process from ¬ to ª and flashes alternately

with the set temperature. Once the set temperature

has been reached, an audible signal sounds and

the heating indicator goes out. The selected

temperature will then be displayed again.

8 Once the signal has sounded, take the lid off and

add the food. Keep the lid on during cooking.

Note: Do not cover the pan when using the "Frying

with a large amount of oil in the saucepan" function.

You can also activate the cooking sensor function via

the wireless temperature sensor. Proceed as follows:

▯ Set down the cookware and press the ¨ symbol on

the wireless temperature sensor.

▯ Select the hotplate using the twist knob.

When the function is ready, the default temperature of

95°C is displayed.

Switching off the cooking sensor function

You can deactivate this function in a number of ways:

▯ Select the hotplate and touch the ¨ symbol.

▯ Select the hotplate and set the temperature to ‹

using the twist knob.

▯ Press the ¨ symbol on the wireless cooking

sensor.

A signal sounds and the ¨ symbol goes out in the

hotplate display. The function is deactivated.

Â 



Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gaggenau CV282 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gaggenau CV282

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info