Bedienungsanleitung Gardena AquaContour automatic - 8133 (Seite 16 von 70) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

820996

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

6. MAINTENANCE

6.1 Replace batteries [ Fig. M1 ]:

If the Set LED 1 and Set LED 2 start flashing

every 8 seconds, the batteries have to be

replaced.

The programmes remain unchanged.

1. Turn the battery cover e on the bottom of the

Large-Area Irrigation AquaContour automatic

anticlockwise 1 and pull out carefully 2 (bayonet

coupling).

2. Remove battery holder r and insert 4 batteries

(1.5 V round cells type IEC LR14).

When doing so, ensure correct polarity + / −.

3. Re-insert battery holder r.

4. Fit battery cover e in reverse order.

6.1.1 Test battery:

The batteries must be tested after each

irrigation!

If no irrigation or programming is being made, the

sprinkler goes into “sleep mode” (the green Auto-

LED 6 does not light up and the red Set-LED

blinks every 8 seconds).

v During “sleep mode” (the green Auto LED 6

does not light up) press the two buttons “+”

button 2 and “−” button 3 for 4 seconds.

7. TROUBLESHOOTING

7.1 Troubleshooting table:

Problem Possible Cause Remedy

Irrigation width smaller than

on initial start-up Dirt filter soiled. v Clean dirt filter.

Tap not opened sufficiently. v Open tap further.

Water pressure too low. v Increase water pressure /

water supply.

Batteries are flat. v Replace batteries. If the bat-

teries are flat, the range is

reduced to the minimum level.

Irrigation range is programmed

incorrectly.

v Reprogramme irrigation range.

Watering pattern uneven Nozzles soiled. v Clean nozzles.

Nozzle head soiled. v Clean nozzle head.

Nozzle head damaged. v Contact GARDENA Service.

5. STORAGE

5.1 To put into storage:

The product must be stored away

from children.

1. Remove batteries from the Large-Area Irrigation

AquaContour automatic.

The programmes remain unchanged.

2. Store the Large-Area Irrigation AquaContour

automatic in a dry place protected from frost.

1. Open water supply.

When using for the first time, the minimum

range (2.5 m with a flow pressure of 2 bar at

the large-area irrigation) is selected.

2. Press OK button 4.

A green Auto LED 6 lights up.

3. Select program: keep pressing Menu button 1

until the required Set LED 5 (1 or 2) lights up.

The required programme 1 or 2 has been

selected and can now be programmed in.

4. Turn the nozzle head w on the orange ring

by hand to the left-hand sector limit (in the

example P1) and hold.

5. Use the two buttons “+” button 2 and

“−” button 3 to set the range so that it

reaches P1.

6. Press OK button 4.

The green Auto LED 6 lights up for 1 second

and the first point P1 has been stored.

7. Turn the nozzle head w on the orange ring

by hand to the next irrigation point (e. g. P2)

and hold.

8. Use the two buttons “+” button 2 and

“−” button 3 to set the range so that it

reaches to the next irrigation point (P2 for

example).

9. Press OK button 4.

The green Auto LED 6 lights up for 1 second

and the point has been stored.

10. Repeat the process from steps 7 to 9 until

the right-hand sector limit is reached (in the

example P10).

11. Press Menu button 1.

The red Set LED 5 goes out, programming is

complete, and the green Auto LED 6 lights up

for 1 minute. The Auto LED then flashes every

10 seconds.

12. Release nozzle head w and check contour

area watered.

13. If the contour is watered correctly, close the

water supply.

Information about programming:

As soon as the first point is programmed, any

existing programme will be deleted. After pro-

gramming has been completed, no further

points can be deleted or added later on. If the

contour has not been set as required, repro-

gramming with more points will have to be car-

ried out. If no button is pressed for 60 seconds

during programming, programming will be auto-

matically ended and the contour stored.

4.3 Start / end watering [ Fig. F1 ]:

Before irrigation can be started, the Large-

Area Irrigation AquaContour automatic

must have been programmed.

1. Fit the Large-Area Irrigation AquaContour

automatic onto one of the two ground markers

with the 2 spikes (see 3. Initial Operation

lnstall ground marker in ground).

2. Select sector stops according to location

(see 4. OPERATION Select watering sector).

3. Press OK button 4.

The green Auto LED 6 lights up.

4. Select programme: Keep pressing Menu but-

ton1 until the required green Auto LED 6

(1 or 2) lights up.

The required programme 1 or 2 has been

selected.

4.3.1 Start watering:

v Fully open water supply.

Watering will start automatically and the contour

of the selected watering sector will be watered.

4.3.2 End watering:

v Close water supply.

Watering will end. The programme remains

unchanged.

GAR_08133-20.960.11_2024-06-05.indb 16GAR_08133-20.960.11_2024-06-05.indb 16 05.06.24 11:2005.06.24 11:20

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gardena AquaContour automatic - 8133 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info