Bedienungsanleitung Garmin TR-1 Gladiator (Seite 20 von 36) (Englisch)

583791

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

To do an outward spiraling search from the waypoint, setup the

special nav function

buttons for search

patterns.

1. Press and hold the [Setup] button on the handheld.

2. Press and light up the [number 9] LED on the handheld.

Release the [Setup] Button.

3. When you are near the waypoint you want to search

from, select “go to” this waypoint on your GPS.

4. With the pilot in heading hold, press and release the [GPS

button] on the handheld, and then press and release one of

the Chevron Buttons. If you pressed the [Right Chevron]

button, the waypoint will remain on your starboard side as

the spiral search unwinds.

Search Pattern

To do an outward spiraling search from a waypoint, setup the special function buttons for search

patterns. (See page 28 Selecting Special Functions) When you are near the waypoint you want

to search from, select go to this waypoint on your GPS. With the pilot in heading hold, press

and release the GPS (Select Load) button and then press and release one of the Bent Arrow

buttons. If you pressed the Bent Right Arrow button, the waypoint will remain on your

starboard side as the spiral search unwinds. The spacing between the spiral laps is set with setup

code 249.

Search Pattern (GPS Steering)

Return to heading hold by pressing one of the straight arrow buttons. An example of the search

pattern is shown in the figure below.

o change the setup options for Search Pattern:

You must be in [Auto] or [STBY] mode before selection process can start

1. Press and release

the [Setup] Button. The [Setup] LED will illuminate to indicate the system is

ready to take setup commands (button pushes).

2. Select the Setup Code you want to use by pressing and releasing the buttons labeled 2 &5 until the

appropriate LEDs are lit. (See the Code and Setup Choices on the table below)

3. Increase an adjustable parameter one step by each press of the [UP Arrow] button. When the

parameter is adjusted to its maximum value, the [Up Arrow] LED will light. The parameter is

adjusted and is in use by the autopilot immediately.

4. Decrease an adjustable parameter one step by each press of the [Down Arrow] button. When the

parameter is adjusted to its minimum value, the [Down Arrow] LED will light. The parameter is

adjusted and is in use by the autopilot immediately.

5. To save the changes into permanent memory and make the selected function into a

startup default: Press and release

the [Setup] button (the [Setup] LED should be lit),

and then press and hold

the [Select Load] button. While holding down the [Select Load]

button, press and release the [Deckmount] On/Off button quickly, then release the GPS

[Select Load] button.

Description Code Setup Options (Parameters) Factory Setting

Search Spacing 25 50 to 1,000 ft, by 50 ft. increments 50

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin TR-1 Gladiator Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info