Bedienungsanleitung Garmin TR-1 Gladiator (Seite 21 von 36) (Englisch)

583791

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

How to Change Settings Using The Table of Setup Codes

1. Autopilot must be in heading hold [Auto],[Standby], or [ GPS Track] mode before selection

process can start. ( [Auto] LED solid on or [STBY] LED on solid or [GPS Track] LED solid

on.)

2. Press and release

the [Setup] Button. The [Setup] LED will illuminate to indicate the

system is ready to take setup commands (button pushes).

3. Select the Setup Function you want to use by pressing and releasing the buttons labeled 1

through 9 until the appropriate LED’s are lit. (See the Table of Setup Codes and values changes

on the following pages)

4. Increase an adjustable parameter one step by each press of the [UP Arrow] button. When

the parameter is adjusted to its maximum value, the [Up Arrow] LED will light. The parameter

is adjusted and is in use by the autopilot immediately.

5. Decrease an adjustable parameter one step by each press of the [Down Arrow] button.

When the parameter is adjusted to its minimum value, the [Down Arrow] LED will light. The

parameter is adjusted and is in use by the autopilot immediately.

6. You can stay in [Setup] and adjust more than one parameter.

7. Compass Calibration, and autotune are setup conditions that take the system over. You

can get out of compass calibration by turning the power off and can back out of autotune by

pressing any button on the remote. Setting compass North will cause the autopilot to turn off

after the compass realigns. The button sequences for their operation are given in the table of

Setup Codes on the following pages.

8. To view the operating value of an adjustable parameter, enter its code per the Table of Setup

Codes, then press and hold the [Select Load] GPS button. The LED on the [Up Arrow] button

will blink the number of tens the parameter is set to and the LED on the [Down Arrow] button

will blink the number of ones the parameter is set to. For example, if the parameter is set to

a current value of 15, the [Up Arrow] LED will blink once and the [Down Arrow] LED will

blink 5 times to indicate the parameter is set to 1 (blink) X 10 + 5 (blinks) X 1. Of course,

when a parameter is adjusted to its minimum or maximum value, the appropriate LED stays on

solid per steps 4. and 5. above. Note: The number of blinks, like 15 in the example, tells you

how many steps up from the minimum setting.

9. For temporary use of the adjusted parameters: Press and release the [Setup] button to exit

the setup mode.

10. To make the selected Functions into startup defaults

(save the changes into permanent

memory)

: Press and release

the [Setup] button (the [Setup] LED should be lit), and then

press and hold

the [Select Load] button. While holding down the [Select Load] button,

press and release the [Deckmount] On/Off button quickly, then release the GPS [Select

Load] button.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin TR-1 Gladiator Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info