Bedienungsanleitung Garmin TR-1 Gladiator (Seite 26 von 36) (Englisch)

583791

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Your autopilot needs to be setup and tuned to your boat dynamics and motor conguration.

It is important to get the autopilot operating the best in can. The Dockside Setup and the

Sea Trial Setup are steps that must be followed to achieve the best performance from the

TR-1 Gladiator Autopilot. Have patience and try to do the Sea Trial Setup on a nice calm

day. Follow the directions below. These steps are in a sequence to help keep you from

making any errors. If you have any questions, please call us at 1-866-559-0229.

1. Turn autopilot system on. Press the deckmount (on/off switch) on, the deckmount will

blink slowly for 30 seconds during startup. The system will automatically go into standby

mode, and the deckmount will then blink rapidly. No functions are available during

startup. You will be using the handheld and deckmount switch to enter codes, change, and

save the values of the parameters. Parameters and their values are on the Table of Setup

Codes, (Pages 25-27)

2. Lock to Lock times. Count the number of turns it takes your helm to go from lock to

lock and adjust the parameter of code 26 to match. (Factory default is set at 4.5) The value

of code 26 can be seen in the blink code ashed on the up and down arrow buttons on the

handheld. Press and light up the [Setup] LED , press and light up numbers 2 & 6, [Code

26]. Press and hold the [Select Load] (GPS) button. The number of turns is 1/10th of the

blinked code + 1. Example: if the blinked code is 44 (The up arrow will blink 4 and the

down arrow will blink 4) the number of turns is (44 + 1)/10 = 4.5 turns lock to lock.

3. Helm displacement. The value of [Code 269] should be set to reect the helm

displacement. (Factory Default is set at 1.7). Press and release [Setup] button. Press and

light up [Code 269] on the handheld. By pressing and holding down the [Select Load]

(GPS) button on the handheld, the up and down arrows will blink to reect the helm

displacement code. The helm displacement is usually written on the body of the helm

pump. Example: The blinked code for a 1.7 cu in/rev helm would be 16, (the up arrow

blinks once and the down arrow blinks 6) since (16 +1)/10 = 1.7.

4. Verify the direction of steering is correct. Turn the autopilot on and switch from

standby to autopilot. When the right straight arrow turn button is pressed on the handheld

remote, the motor should turn the boat to the right. When the left straight arrow turn

button is pressed on the handheld/remote, the motor should turn the boat to the left. If this

is incorrect use [Code 249] for reversed hoses. Press and release, and light up the [Setup]

LED, press and light up [Code 249] on handheld, if the down arrow is lit, press the up

arrow to reverse hoses. If you change this setting, download changes into permanent

memory by following step 8.

Dockside Setup and Sea Trial Setup of Autopilot

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin TR-1 Gladiator Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info