Bedienungsanleitung Garmin TR-1 Gladiator (Seite 27 von 36) (Englisch)

583791

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Dockside Setup: Steps 1-9 can be done at the dock before heading for open water.

5. RPM Source Conguration. The default setting on the autopilot is set for a Single

Engine. If you have twin engines or more, you will need to change [Code 259] to match

your motor conguration. Twin engines; Press, release and light up the [Setup] LED on

the handheld, press and enter [Code 259] on the handheld. Press the [Up Arrow] TWO

(2) times which is setting the parameter to [(4) Both]. See page 22 code 259 for more

information.

6. Verify the autopilot tachometer (Tach Sensor Cable) is functioning properly. With

the engine(s) running. Press, release and light up the [Setup] LED on the handheld, and

press and light up [code 35]. Press and hold the [Select Load] GPS button and you

should see the [Up Arrow] and [Down Arrow] LED’s blink your port engine’s RPM. For

example, when the [Up Arrow] LED blinks 2 times and the [Down Arrow] LED blinks

5 times your engine is running at 2500 RPM. [Code 36] works the same way as code 35

for the starboard engine instead of the port engine. The autopilot tachometer system has a

lower limit setting of 200 RPM. If needed, adjusting [Code 267] (pulses per rev) to make

your autopilot tachometer match the tach on your dashboard.

7. Transition RPM. This is the RPM at which your boat transitions from displacement

to planing speed. [Code 348] is set to a factory default of 3000 (2 blinks of the [Up

Arrow] LED and 9 blinks of the [Down Arrow] LED +1). You should set it to your

boat’s transition RPM. (Example: Say that your planing speed is at 2500 RPM’s; With

the [Setup] LED lit, press and light [code 348], since the factory default is 3000 which is

2 blinks of the up arrow and 9 blinks of the down arrow (The value can be seen with the

[Setup] LED lit, press and hold the [Select Load] GPS , release the select load button, then

click the down arrow 5 times; that will set your transition RPM’s at 2500.) If you don’t

know what the transition RPM is, you will need to do this as part of your Sea Trial Setup.

8. Download to permanent memory the parameters you have adjusted so far. (This

must be done) With the [Setup] LED lit, press and hold the GPS [Select Load] button

- the [load] LED should illuminate on the handheld, while still holding down the [Select

Load] button, press and release the [Deckmount], on/off button quickly, then release the

[Select Load] GPS button.

9. Verify NMEA Connections: Verify that the NMEA connections for the GPS are

functioning. Turn on the GPS. With the Autopilot in [Standby], press and release

[Setup] button on the handheld. Press and light up the number 4 and the number 8

LED’s[ Code 48]. If the [up arrow] LED lights when you hold down the [Select Load]

(GPS) button, the autopilot does not acknowledge the validity of the GPS data.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin TR-1 Gladiator Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info