Bedienungsanleitung Gorenje k 7708 e (Seite 15 von 18) (Englisch)

326973

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

179732

Instructions for use, installation and connection

Nozzle chart

Type of gas,

pressure

Auxiliary burner Normal burner Large burner Triple burner

Wobe number Standard Fast

max min max min max min max min max min

Natural gas H

Wo=45,7÷

Nominal heat input

(kW)

1 0,36 1 0,36 1,90 0,46 3 0,76 3,5 1,56

54,7 MJ/ m

, Consumption (l/h) 95,21 34,4 95,21 34,4 180,9 43,8 285,64 72,4 333,2 148,5

Natural gas E , Nozzle mark (1/100mm) 77 78 104 129 - 140

•

Natural gas E+

Wo=40,9÷

54,7 MJ/m

G20,

p=20mbar

Nozzle code 162081 162082 162083 162084 162085

Liquid gas 3+,

3B/P

Nominal heat input

(kW)

1 0,36 1 0,36 1,90 0,46 3 0,76 3,5 1,56

Wo=72,9÷

Consumption (g/h) 71,7 26,2 71,7 26,2 138,1 33,4 215,0 55,3 254,5 113,4

87,3MJ/m

G30

Nozzle mark (1/100mm) 50 29/24 50 29/24 69 33/26 87 43/33 93 57/57

p=30 mbar Nozzle code 162162 162162 162164 162165 162166

• Built-in regulation knobs are intended for liquefied gas. In case of natural gas (municipal gas line) they need to be set according to

the required gas flow (unscrew for maximum 1,5 turn from the tightened position).

Nozzle code for minimum varies with different manufacturers. First digit from the pair represents IMIT, and the second one

COPRECI.

Burner heating input is indicated according to the maximum caloric value of gas Hs.

Warning: this work may be performed only by qualified expert, authorized by the gas distribution company or by the

authorized service!

Conversion to another type of gas

• For the conversion procedure the appliance need not be

pulled out from its location.

• Before starting to work on conversion, disconnect the

appliance from the mains.

• Replace the existing nozzles of declared nominal heat input

with adequate nozzles for the new type of gas (see table).

• Adjust the nozzle for the minimum heat input rate as long as

it requires to arrive at the minimum heat input.

• Never unscrew nozzles for minimum heat input rate for more

than 1,5 turn.

• After the conversion is done, stick the new sticker with the

actual gas specifications of the appliance over the old one.

• Check that electrical cables, thermostat probe and thermal

elements are located away from the gas jet!

Setting elements

Elements for regulation of cooking burners are accessible

when the control panel is removed.

• Remove the cooktop grid and burner crowns with caps.

• Remove the control buttons.

• Unscrew bottom tightening screws from the control panel

and remove the panel.

Cooking zone burner (fig. 1 )

1 Burner crown cap

2 Burner crown with

burner cap support

3 Thermal probe

4 Ignition plug

5 Nozzle

Triple-ring burner(fig. 2)

5 nozzles

Safety gas faucet (fig. 3)

13 Setting screw for

minimum heat input rate

Non-safety gas faucet (fig. 3a)

13 Setting screw for

minimum heat input rate

Elements to be replaced or reset when altering the type of

gas

Cooking zone burner Fig. number Element code

Nominal heat input

1,2 5

Minimum heat input

3, 3a 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gorenje k 7708 e Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info