Bedienungsanleitung Gossen Metrawatt METRISO PRIME (Seite 4 von 14) (Englisch)

590654

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

4 GMC-I Messtechnik GmbH

Errors and Extraordinary Strains

If it may be assumed that the instrument can no longer be operated safely, it must

be removed from serviced and secured against unintentional use. Send the instru-

ment to the Repair and Replacement Parts Service Department; see Chapter 10,

page 13. Safe operation can no longer be relied upon,

• if measurement cables are damages,

• if the instrument demonstrates visible damage,

• if the needle gauge no longer responds,

• if one of the LEDs is defective,

• if the instrument no longer functions,

• after lengthy periods of storage under unfavorable conditions.

Observe the following safety precautions:

• The instrument may only be operated with batteries or storage batter-

ies. Mains driven power packs are not permissible, because the use

of such is life endangering.

• Be prepared for the occurrence of unexpected voltages at devices

under test. (For example, capacitors can be dangerously charged.)

• Make certain that measurement cables are in flawless condition, e.g.

no damage to insulation, no creases, no interruptions etc.

Attention!

Do not touch the test prods or the device under test during

voltage testing! High-voltage of up to 5kV is present!

Attention!

Accumulation of Moisture:

An accumulation of moisture on

the tester, on the measurement cables or on the DUT must be

avoided, because leakage currents may be caused by high-voltages

at exposed surfaces. Even isolated components may carry high-

voltages.

Note



Overvoltage Influence: If the reversible fuse (PTC thermistor)

responds to an overvoltage or an extraneous voltage, measure-

ment may not be resumed immediately. A cool-down period of

approximately 2 minutes must be observed.

Using the test probes (Electrical Safety)

Attention!

Measurements per DIN EN 61010-031 may only be per-

formed in environments in accordance with measuring cate-

gories III and IV with the safety cap attached to the test probe

at the end of the measurement cable.

In order to establish contact inside 4 mm jacks, the safety caps have to be

removed by prying open the snap fastener with a pointed object (e.g. the

other test probe).

Meaning of symbols on the instrument

Warning concerning a point of danger

(Attention: observe documentation)

Caution: high-voltage!

A life endangering high-voltage of up to 5 kV

is present at the test prods.

CAT II/III/IV Measurement category II/III/IV device

Continuous double, or reinforced insulation

Seal of approval from VDE testing authority

This device and the inserted (rechargeable) batteries may not be

disposed of with the trash. For information regarding the WEEE

mark can be accessed on the Internet at www.gossen-

metrawatt.com by entering the search term ’WEEE’.

Indicates EU conformity

Maximum rated voltage 300 V

600 V

1000 V 5000 V

Measuring category

CAT IV CAT III CAT II

—

With safety cap attached

——

Without safety cap

— — 

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gossen Metrawatt METRISO PRIME Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gossen Metrawatt METRISO PRIME

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info