Bedienungsanleitung Gossen Metrawatt SECULIFE ST HV (Seite 18 von 72) (Englisch)

590775

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

18 GMC-I Messtechnik GmbH

8 Configuring Device Parameters

General device

parameters can be

configured and

saved with the se-

lector switch in the Setup position.

Select a menu and acknowledge.

Select parameter and acknowledge, change setting and acknowledge.

Limit values ...

Settings x / – = function activated / deactivated

Illumination Background illumination for the LCD. One of three

different conditions can be selected* with the up and

down scroll keys: x: continuously on, –: off

numbers 1 through 9: duration in minutes after which

illumination is automatically deactivated.

Test time Duration of a single test (0 … 255 s)

Reference voltage: Voltage to which leakage current makes reference

(as a rule nominal line voltage)

Earth fault: During the short-circuit test, testing is also performed

to determine whether or not a connection exists

between L/N and PE (short-circuit to exposed con-

ductive part). We assume that a short-circuit to an

exposed conductive part exists in the event of leak-

age current greater than 15 mA from L/N to PE. This

value should be increased for some DUTs (in particu-

lar high-current consumers), because greater leak-

age currents are present.

Mains wait

Line voltage is first applied to the test socket. However,

testing does not begin until after the duration selected in

seconds under “Mains pause” has elapsed.

* The background illumination of test instruments equipped with panels produced

as of 2014 can no longer be deactivated.

Automode x: for fully automatic test sequences the messeges

are mainly suppressed

Test Sequence ...

Settings x / – = function activated / deactivated

Single-fault

If the single-fault condition has been activated, the test

is interrupted as a failure as soon as an error occurs.

Auto Class PSI Test results (passed or failed) for the various selector

switch positions are automatically assigned to the 8

statistics channels.

inc. Service Error Measurement results are compensated by taking

service error into consideration (measuring error).

IT Network Testing in IT systems can be performed by suppress-

ing tests for U

PE-N

. The U

PE-N

test determines

whether or not voltage is present at PE.

(Leakage current measurement results may other-

wise be distorted.)

Acst Sig, Seq

Acoustic signal is generated for: Incorrect connection of the

DUT, error in the electrical supply system, next test step.

Acst Sig, Meas Acoustic signal is generated for: Measured value

fluctuations, test current polarity reversal

Auto meas. point Prerequisite: Feature KD01*. An acoustic signal indi-

cates whether or not the probe is connected to the

protective conductor. The test sequence is run auto-

matically. Rapid signal frequency: probe connected

to PE; slow signal frequency: next measuring point

Direct Print-Out

Prerequisite: Feature KE01*, see chapter 18 on page 59.

Reports … Reports which have been saved to memory can be

selected from a list with an ID number and displayed

(see chapter 18 on page 59).

Select template a report template can be selected for print-out from

of 5 different templates.

SECUSTORE Optimize data transfer for the SECUSTORE adapter

connection (in this configuration, no data can be

saved to the (P)SI module). Neither is a test report

signalled to the RS232 interface.

Service … – Time and date settings (if a (P)SI module is used,

the same time and date must also be entered to the

(P)SI menu)

– Service functions (password required)

Setup

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gossen Metrawatt SECULIFE ST HV Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info