Bedienungsanleitung Graupner MX-16 HoTT (Seite 173 von 200) (Englisch)

467107

173

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

173

Programming example - ﬁxed-wing model

MIX1 c1 c1

trv

0%offs

ASYSYM

–100%

Now move to the “Offs” line: when you do this, the SYM

and ASY ﬁelds are replaced by STO and SET. With

the STO button highlighted, move the Ch 1 stick to the

“OFF” position you have selected, and then touch the

central SET button of the right-hand touch-key: the value

to the right of “Offs” now changes from 0% to approx.

+100%, and the graphic display of the mixer curve

displayed on the right also changes accordingly:

MIX1 c1 c1

trv

+100%offs

SETS TO

–100%

If you now touch the  buttons of the left-hand touch-

key simultaneously to move to the …

“Servo display” menu (page 133),

… you can immediately check the effect of the settings

you have entered so far: with the mixer switched off,

the bar display for Channel 1 follows the movement of

the Ch 1 stick. With the mixer switched on it stops - as

shown - at around -100%.

Once you are conﬁdent that the direction of the Ch 1

stick is “correct” as far as the motor is concerned, the

next step is to ensure that you can switch its effect on

the motor on and off, so that you can also control the

braking system. This is carried out in the …

“Free mixers” menu (pages 127 … 132)

typ fro

… where you need to program a free mixer “c1  c1”.

When you have done this, use the arrow button  of the

left or right-hand touch-key to move to the column above

the symbol, and assign your selected “change-over

switch” to this mixer; for example SW 2. This is done by

activating the switch assignment by touching the central

SET button of the right-hand touch-key, and moving the

switch from “forward” to “back”, i. e. towards you.

With the mixer switched on, move to the column above

the

symbol using the arrow button  of the left or

right-hand touch-key, and then on to the second screen

page by touching the central SET button of the right-

hand touch-key.

At this point you should set an initial SYMmetrical mixer

value of -100%.

“Servo settings” menu (page 92)

r ev cent

trav

100%

… and reverse the direction of servo 1.

For safety’s sake you should check this setting now,

before you continue with the programming procedure.

Take the transmitter and model to a location where it

is safe to run the motor. Switch the transmitter on, and

move the Ch 1 stick to the motor “OFF” position, i. e. ei-

ther fully forward or back. Hold your model ﬁrmly, or ask

a friend to hold it for you. Check that the propeller is free

to rotate without causing havoc, then connect the ﬂight

battery and switch your model’s receiving system on.

If the motor does NOT run when the stick is in the “for-

ward” or “back” position (as appropriate), then everything

is in order. However, please check the system anyway by

gradually advancing the stick until the motor begins to

run. When you are satisﬁed, stop the motor, then switch

off the receiving system in the model and ﬁnally switch

off the transmitter.

Note:

If the motor does not start, or spins in the wrong direc-

tion, this indicates that there are other problems which

you must correct before you continue with programming.

For example, check the wiring of your motor, and refer

to the operating instructions supplied with your speed

controller.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MX-16 HoTT Seite 173

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner MX-16 HoTT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info