Bedienungsanleitung Graupner Ultramat 17 (Seite 19 von 33) (Deutsch, Englisch, Französisch)

467070

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

3736

Button click / buzzer settings

The purpose of this sub-menu is to adjust the settings for the audible sounder.

Button click: Every time you press a button you will hear a “click” sound to confirm your action. This

sound can be switched on (EIN) or off (AUS).

Buzzer: When the screen displays a warning, “completed” or an error message etc., the inte-

gral buzzer sounds at the same time to alert you. In this program point you can select

buzzer off (AUS), or the length (10 sec. or no time limt) of the audible warning.

Erase user settings

This menu provides the means to reset all the user settings

to their standard default values:

Initial power-on program : NiCd Automatik

NiCd Delta Peak : 20 mV / cell

NiMH Delta Peak : 15 mV / cell

Charge termination delay : 3 min

Safety timer : 120 min

Initial power-on current : 2.5 A (NiCd, NiMH, PB)

Car battery low voltage : 11.8 V

Button click : ON

Buzzer setting : 10 sec.

___________ _____

Clear

User Settings

___________ _____

Clear

***erased***

DEC

INC

___________ _____

Buzzer

OFF

___________ _____

Buzzer

no time limit

___________ _____

Buzzer

off after 10sec.

DECINC

___________ _____

button click

___________ _____

button click

OFF

DECINC

ENTER

Car battery low voltage cut-off

If the charger is connected to a car battery which is not

required to start a car engine at the end of the session, then

it is safe to discharge it to a lower level.

The charger allows you to set an alternative value of 10.5 V,

which enables you to exploit the maximum capacity of the car

battery without deep-discharging it excessively.

The unit does

not store the alternative setting, so you must

reset it (if required) every time you start using the charger.

___________ _____

low voltage

cut off.= 11.8V

___________ _____

low voltage

cut off.= 10.5V

DECINC

NiCd / NiMH charge termination delay

At the start of the charge process the unit initiates a delay time

which suppresses automatic charge termination during this

(delay) period.

This means: during this delay period the charge

voltage is

not monitored, and the battery is charged for at

least the set length of time! The charge termination delay is

only effective n the NiCd and NiMH charge programs.

Initial power-on current (NiCd, NiMH, Pb)

You can select the charge / discharge current which is to be

set automatically when the charger is connected to the car

battery. In this program segment the value can be set sepa-

rately for each of the charge programs (NiCd, NiMH, LiIo,

LiPo, Pb).

___________ _____

charge cut-off

delay time =3min

DEC

INC

NiCd / NiMH safety timer

The value you set for the safety timer must be generous enough to allow a full charge of the battery.

As a practical guide we recommend a time which is about 30% longer than the expected charge

period; naturally, this varies according to the charge current you have set. Example: 1.8 Ah battery,

charge current 3.6 A -> charge time = 1.8 Ah / 3.6 A - 0.5 hours = 30 min +30% = safety timer =

40 min.

Warning: if you connect an already fully charged battery with the purpose of topping it up, it will be

charged for at least the delay time you have selected, and could then get very hot.

Caution - explosion hazard!

___________ _____

NiCd start curr.

2.5A

DEC

INC

This is particularly useful if you always

use the same charge current, as it avoids

the necessity to select the value sepa-

rately each time you use the charger.

In any case we recommend that you set

a “starting point” value of 2.5 A, as this

avoids the need to run through the enti-

re range every time you start using the

charger.

NiCd start curr.

3.7A

NiMH start curr.

3.7A

Lithium-Start

1.2A

Pb start curr.

1.2A

ENTER

Maximum Automatic current

In this program the charger detects the types of battery

connected and adjusts the charge current accordingly, to

avoid overcharging the pack.

The maximum charge current can be set using the INC /

DEC buttons

before you connect the battery to be

charged.

The charge process is terminated according to the values

set by the user for „NiCd Delta-Peak Termination Voltage“,

„Charge Termination Delay“ and „Safety Timer“.

___________ _____

NiCd max. curr.

automatic: 2.5A

DECINC

___________ _____

safety timer

120 min.

DECINC

When you start a charge process, the integral safety timer

automatically starts running at the same time. The safety

timer is designed to prevent catastrophic overcharging of

the battery on charge if the pack proves to be faulty, or if the

“battery full” detection circuit malfunctions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner Ultramat 17 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner Ultramat 17

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info