633026
7
Zoom out
Zoom in
Vorherige Seite
1/16
Nächste Seite
7
LED BUTTON
CONDITION
The DEFAULT
programming are in “bold”
ALARM SYSTEM
FUNCTION
NUMBER OF
PRESSES
OF THE LED
BUTTON
NUMBER OF
LED BUTTON
/LED FLASHES
FOR THE
FUNCTIONS
STATUS CHECK
LED OFF LED ON
Self-coding indicators
impulses number
1 1
Disabled
Enabled
Switches/Discriminators
signals stabilizer
2 2 Deactivated
Activated
Memorisation of
switches/discriminators
signals only after actuator
signals
3 3
Disabled
Enabled
Memorisation of actuator
signals of changeable type
4 4 Disabled
Enabled
Anti-hijack door signal
stabilizer
5 5
Deactivated
Activated
Acoustic signal when
arming/disarming the alarm
system
6 6 Deactivated
Activated
Visual signal when
arming/disarming the alarm
system
7 7
Deactivated
Activated
Courtesy light switching on
when disarming
8 8
Deactivated
Activated
To modify the settings proceed as follows:
1 - Press the LED BUTTON the number of times corresponding to the function you wish to
check or modify. The alarm generates an acoustic signal for each press.
Before showing the function state, the alarm system will generate acoustic signals and the
LED BUTTON will flash. For example: if you wish to check the function state “Acoustic signal
when arming/disarming the alarm system”, you will have to press the LED BUTTON 6 times,
check that it flashes 6 times and the LED BUTTON remains switched on (acoustic signal
activated) or switches off (acoustic signal deactivated).
2 - When the LED BUTTON shows the function state you are checking (the LED BUTTON
switched on or off), it is possible to modify the alarm system function condition by pressing
the same LED BUTTON.
3 - Once the function state has been selected, the LED BUTTON will flash to indicate that the
new condition has been memorised. If the LED BUTTON isn’t pressed again, or the ignition is
switched off within 2 minutes, the alarm system comes out from the set condition automatically.
4 - At this point, the alarm system will emit a long acoustic signal to confirm you have come
out from the SET FUNCTIONS.
When the alarm system functions have been programmed carry out the DOORS LOCK/
UNLOCK SIGNALS SELF-CODING (page 8).
7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für GT 800-2 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info