Bedienungsanleitung GT 800-2 (Seite 9 von 16) (Englisch)

633026

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

7.0 - RAPID TEST

WARNING:

- Ensure that the alarm is disarmed.

A - Earth the GREEN/YELLOW wire until the alarm system emits a long acoustic signal and

the LED BUTTON starts flashing.

B - After about 10 seconds the alarm system will emit 3 visual (indicators)/acoustic signals

and it will enter automatically the RAPID TEST function. The alarm system can be considered

correctly installed if:

1 - The PINK wire has a positive signal (+12V) output and the additional sensors/modules

connected to this wire activate.

2 - When opening one of the doors (GREEN/BROWN or GREEN/BLUE wires) and the bonnet/

boot (GREEN wire) you will obtain a visual (indicators)/acoustic signal.

3 - When you activate an additional sensor (GREEN/BLACK wire) you will obtain 2 flashings

of LED BUTTON and a visual signal (indicators).

4 - When you activate the ultrasonic sensor you will obtain a visual signal (indicators).

To test the alarm, remove all possible items that may create movements and ensure that

doors and windows are closed. Introduce your arm through the gap and move it around; the

alarm system indicators will flash to confirm correct operation. To increase the sensitivity, turn

the adjuster close to the main alarm connector clockwise (see page 4).

Warning: this procedure is one of the most important correct alarm operation. To check tthe

sensitivity, move your arms across the outside of the window and the soft top roof, this should

not trigger the alarm. Only the introduction of an object should trigger the alarm.

5 - If you press the ANTI-HIJACK FUNCTION reservation button (BLACK/WHITE wire) you

obtain a visual (indicators)/acoustic signal.

6 - When the ignition key is ON you will obtain an acoustic signal (if an additional GT 843

siren is connected, this will sound for about 1 second).

6 - Unlock the vehicle using the original remote control, after a couple of seconds the alarm

will emit 2 visual signals (indicators), and 3 acoustic signals indicating the end of self coding

and the doors will unlock.

Warning: The procedure can be considered carried out correctly only if the operations are in

compliance with the points 5 and 6. On the contrary wait that the alarm system comes out

automatically from the procedure (the alarm system will emit an acoustic signal).To repeat

the procedure disconnect the positive leave for a few seconds and then reconnect. Start the

procedure again from point 1.

Note: supposing that the self-coding procedure has been completed correctly, but you want

to repeat it, for example in the case of the alarm command wires connection (i.e. RED/BROWN,

YELLOW/BROWN, RED/GREY AND YELLOW/GREY wires) has to be changed, it is

necessary to repeat the signals self-coding procedure from the point 1, remember to

disconnect the alarm system power supply for some seconds.

If a self-coding procedure hasn’t been correctly carried out the system can only be

disarmed by the “GT CARD CODE” (see the relative section). Once the alarm is

disarmed, proceed with the self-coding before using the original vehicle’s remote control

handset.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

GT 800-2 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info