Bedienungsanleitung Gude TKGS 1800 (Seite 20 von 152) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch)

624753

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

Caution

Tighten the height changeover screw completely

(Fig. 17), turn it right completely, (a position

opposite to that in the bench mood)

Fit the chips guard for the trimming and mitre

mood according to the figure under the rotary

bench (Fig. 18). The chip guard is to be hung in

two eyes on the saw bench and than screwed on

at the opposite side with two screws attached.

(Fig. 19). If no extraction facility is used, connect

a chips collecting bag to one of the extraction

outlets. .

Now, the saw is ready to work in trimming

and mitre mode.

Operation

Unplug the unit before any setting of the

saw

Cutting Angle Set-up (Fig. 20+21)

• The blade adjustment 0° - 45° may be read

on the scale. By loosening the lock lever

(Fig. 20) and tilting the saw, the cutting

angle may be changed.

• The blade adjustment may be changed by

loosening the screw (Fig. 21) and turning

the saw.

Unit Switching on/off

• Press “green button I” to switch the unit on. .

• Press “red button 0” to switch off.

There is an emergency switch on the machine.

Longitudinal Sections

• Se the parallel stop at the required width in

relation to the blade.

Put the piece to be worked on the bearing

area, the wider/flatter end should be seated

on the saw bench flat wise

Caution: Keep the safety distance from the

blade.

Chamfer Cuts

• Fasten the piece to be worked according to

the figure using a clamp.

• Loosen the lock lever and set up the

required angle.

• Be careful to have the splitting wedge

aligned with the blade at any time.

• Secure the lock screw again.

• Switch the machine on, press the saw down

carefully and cut.

Cross Sections

• Insert the transverse stop into one of the two

grooves of the bench and set up the required

angle.

• Switch the machine on and use the

transverse stop to move the piece to be

worked to the rotating blade carefully.

Caution: Always hold the piece firmly,

never cut a piece held loosely

Splitting Wedge Set-up (Fig. 17+25)

• Loosen the screw on the splitting wedge

(Fig. 25), so that the wedge may be shifted

according the given type of the cut.

• Tighten the screw again.

Maximum cuts:

The distance between the bench and the splitting

wedge upper edge ca 10 cm.

Dovetail cuts:

The splitting wedge point 2 mm below the saw

tooth upper point.

The distance between the splitting wedge and the

blade 3-8 mm.

Dovetail Sections

• Move the splitting wedge down so that the

splitting wedge point is 2 mm below the top

point of the saw tooth.

• The distance between the splitting wedge

and the blade should be 3-8 mm again. .

• Insert the transverse stop into one of the saw

bench groove and set up the required angle.

• If the blade is to be adjusted askew as well

the groove preventing contact of your had

and the transverse stop with the blade guard

should be used as well.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude TKGS 1800 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info