Bedienungsanleitung Gude TKGS 1800 (Seite 21 von 152) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch)

624753

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

Caution: Hold the piece firmly, never cut a

piece that is held loosely.

The dovetail cut having been completed, the

guard has to be fitted back in the place.

If the machine is in use in confined rooms, it has

to be connected to a suitable dust extracting

facility or a dust collecting bag must be attached

to the chips outlet neck (Fig. 17), the bag is

included in the delivery.

Operator Safety Instructions

• All the safety and protection facilities have to

be installed in place before switching the

machine on.

• Never cut pieces of wood so small that they

cannot be held safely. .

• The blade should turn freely.

• Cutting wood treated or worked in any way

beforehand, be particularly careful of nails,

screws etc. Remove all of those before

getting down to work.

• Before switching the main switch on, make

sure that the blade is fitted correctly and the

movable components of the machine are

unconstrained.

• Warning! If in doubt, have the advice of a

specialist at the authorised servicing centre.

• Do not use the machine until you have read

the instruction manual carefully.

• Observe any safety instructions included the

manual.

• Be responsible to the others.

Step-by Step Instructions

Bench Circular Saw

1. Set up the stops according to the cutting

required.

2. Switch the unit on.

3. Slide the piece to be worked slowly and

evenly to the blade using the sliding device

so that the first full cut can be done.

4. Switch the saw off and wait for the blade to

come to standstill.

5. Take the piece out.

Trimming and Mitre Saw

1. Set up the machine according to the cut to be

done.

2. Se the piece to be worked in the clamp (see

also Fig. 29)

3. Switch the machine on

4. Push the unit downwards slowly and carefully

and do the cut.

5. Switch the saw off and wait for the blade to

come to standstill.

6. Remove the piece

Troubles - Causes –

Troubleshooting

CAUTION: ALWAYS CHECK THE THERMAL

PROTECTION FIRST!

Motor will not run

1. No supply to the machine.

Check the supply and supply line, consult a

professional electrician.

2. Thermal sensor has interrupted the supply.

Wait for 5-10 min. and switch on again.

Motor will shut off in the course of work.

1. Motor thermal sensor defective

Have the exchange done by a professional

electrician.

2. Motor circuit breaker switches off for

overloading.

Wait for the motor cool down restart after 5-

10 min.

Overloading

1. The input line too long or its diameter is too

small

The dimension of the extension cable must

be 1,5 mm

2. Blade not sharp as required.

Sharpen the blade.

3. The blade teeth are not bevelled correctly.

Have the teeth bevelled by a professional.

Burnt marks on the piece being worked

1. Blade blunt.

Sharpen/Replace the blade.

Inspections and Maintenance

Unplug the unit before any work on it.

• Use a wet cloth to clean the plastic parts. Do

not use detergents, solvents or pointed tools.

• Wipe any dirt from the table surface, use a

treatment spray.

• If the motor braking time is above 10 s, the

brake wearable parts should be exchanged

by the manufacturer or an authorised shop.

• Prior to every use, remove the dust from the

vents and movable parts. Use a soft brush.

• Oil all the movable metal parts regularly.

Saw Blade Replacement

(Fig. 29+30)

Caution! Switch the unit off and unplug before

any maintenance, adjustment of the blade

replacement.

• Press the lever (Fig. 29) down and keep it

pressed for the blade to get locked. .

• To loosen the blade screw, use the socket or

open-ended spanner Unscrew it clockwise.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude TKGS 1800 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info