683782

Hako Scrubmaster B140R Seite 14

14
Zoom out
Zoom in
Vorherige Seite
1/38
Nächste Seite
Service display
The service display is located in the
hourmeter display.
When turning ON, the following
sequence of information will appear in
the hourmeter display:
– software status for 1 approx.
second, e.g.
– last error found, for approx. 2
seconds (points blink), e.g.
Note: If a defect is still existing, a
buzzer sounds and the red display
turns ON (F).
– hours run, e.g. during operation, the
dot will blink.
Note: on factory-new machines,
the display may read when the key
switch is turned to ON.
This is an internal control code;
display will change to 0 hours after
not more than one hour.
The Hakomatic is serviceable with
this display.
Error display is active either.
If a malfunction occurs during ope-
ration, a 4-digit number will appear
in the display, the 4 dots will start
flashing simultaneously and the
buzzer sounds.
Refer to page 61 for the error code
numbers which you may remedy by
yourself. If the machine does not
operate correctly despite measures
taken, denote the error code and
advise your Hako service center.
H Pilot lamp for battery charge
condition
Upon turning ON the key switch, all
green pilot lamps (b to d) alight in
case of a perfectly charged battery.
During operation the lamps b, c and
d will successively extinguish as the
battery discharges.
A flashing red light (a) indicates that
operation will soon be interrupted
and the buzzer sounds. After 3
more minutes, the red lamp alights
permanently and the brush dive
and the suction turbine will be
switched OFF. The travel drive
assembly remains activated. We
recommend to recharge the batte-
ries at the charging station as soon
as possible.
I Key for additional scrubbing and
vacuuming tool
Note: this key is only operable if
the Hakomatic is equipped with
the ”additional scrubbing and
vacuuming tool” option and the Ha-
ko service center has programmed
the machine accordingly.
Otherwise, ”-OP-” is displayed.
This key turns the water pump and
the suction turbine ON and OFF.
The water and the vacuuming hose
of the scrubbing tool have to be
connected previously.
46
3. 0 1 5
1. 2. 6. 1.
0 2 1 5.
9 9 9 9.
Service display
The service display is located in the
hourmeter display.
When turning ON, the following
sequence of information will appear in
the hourmeter display:
– software status for 1 approx.
second, e.g.
– last error found, for approx. 2
seconds (points blink), e.g.
Note: If a defect is still existing, a
buzzer sounds and the red display
turns ON (F).
– hours run, e.g. during operation, the
dot will blink.
Note: on factory-new machines,
the display may read when the key
switch is turned to ON.
This is an internal control code;
display will change to 0 hours after
not more than one hour.
The Hakomatic is serviceable with
this display.
Error display is active either.
If a malfunction occurs during ope-
ration, a 4-digit number will appear
in the display, the 4 dots will start
flashing simultaneously and the
buzzer sounds.
Refer to page 61 for the error code
numbers which you may remedy by
yourself. If the machine does not
operate correctly despite measures
taken, denote the error code and
advise your Hako service center.
H Pilot lamp for battery charge
condition
Upon turning ON the key switch, all
green pilot lamps (b to d) alight in
case of a perfectly charged battery.
During operation the lamps b, c and
d will successively extinguish as the
battery discharges.
A flashing red light (a) indicates that
operation will soon be interrupted
and the buzzer sounds. After 3
more minutes, the red lamp alights
permanently and the brush dive
and the suction turbine will be
switched OFF. The travel drive
assembly remains activated. We
recommend to recharge the batte-
ries at the charging station as soon
as possible.
I Key for additional scrubbing and
vacuuming tool
Note: this key is only operable if
the Hakomatic is equipped with
the ”additional scrubbing and
vacuuming tool” option and the Ha-
ko service center has programmed
the machine accordingly.
Otherwise, ”-OP-” is displayed.
This key turns the water pump and
the suction turbine ON and OFF.
The water and the vacuuming hose
of the scrubbing tool have to be
connected previously.
46
3. 0 1 5
1. 2. 6. 1.
0 2 1 5.
9 9 9 9.
Service display
The service display is located in the
hourmeter display.
When turning ON, the following
sequence of information will appear in
the hourmeter display:
– software status for 1 approx.
second, e.g.
– last error found, for approx. 2
seconds (points blink), e.g.
Note: If a defect is still existing, a
buzzer sounds and the red display
turns ON (F).
– hours run, e.g. during operation, the
dot will blink.
Note: on factory-new machines,
the display may read when the key
switch is turned to ON.
This is an internal control code;
display will change to 0 hours after
not more than one hour.
The Hakomatic is serviceable with
this display.
Error display is active either.
If a malfunction occurs during ope-
ration, a 4-digit number will appear
in the display, the 4 dots will start
flashing simultaneously and the
buzzer sounds.
Refer to page 61 for the error code
numbers which you may remedy by
yourself. If the machine does not
operate correctly despite measures
taken, denote the error code and
advise your Hako service center.
H Pilot lamp for battery charge
condition
Upon turning ON the key switch, all
green pilot lamps (b to d) alight in
case of a perfectly charged battery.
During operation the lamps b, c and
d will successively extinguish as the
battery discharges.
A flashing red light (a) indicates that
operation will soon be interrupted
and the buzzer sounds. After 3
more minutes, the red lamp alights
permanently and the brush dive
and the suction turbine will be
switched OFF. The travel drive
assembly remains activated. We
recommend to recharge the batte-
ries at the charging station as soon
as possible.
I Key for additional scrubbing and
vacuuming tool
Note: this key is only operable if
the Hakomatic is equipped with
the ”additional scrubbing and
vacuuming tool” option and the Ha-
ko service center has programmed
the machine accordingly.
Otherwise, ”-OP-” is displayed.
This key turns the water pump and
the suction turbine ON and OFF.
The water and the vacuuming hose
of the scrubbing tool have to be
connected previously.
46
3. 0 1 5
1. 2. 6. 1.
0 2 1 5.
9 9 9 9.
Service display
The service display is located in the
hourmeter display.
When turning ON, the following
sequence of information will appear in
the hourmeter display:
– software status for 1 approx.
second, e.g.
– last error found, for approx. 2
seconds (points blink), e.g.
Note: If a defect is still existing, a
buzzer sounds and the red display
turns ON (F).
– hours run, e.g. during operation, the
dot will blink.
Note: on factory-new machines,
the display may read when the key
switch is turned to ON.
This is an internal control code;
display will change to 0 hours after
not more than one hour.
The Hakomatic is serviceable with
this display.
Error display is active either.
If a malfunction occurs during ope-
ration, a 4-digit number will appear
in the display, the 4 dots will start
flashing simultaneously and the
buzzer sounds.
Refer to page 61 for the error code
numbers which you may remedy by
yourself. If the machine does not
operate correctly despite measures
taken, denote the error code and
advise your Hako service center.
H Pilot lamp for battery charge
condition
Upon turning ON the key switch, all
green pilot lamps (b to d) alight in
case of a perfectly charged battery.
During operation the lamps b, c and
d will successively extinguish as the
battery discharges.
A flashing red light (a) indicates that
operation will soon be interrupted
and the buzzer sounds. After 3
more minutes, the red lamp alights
permanently and the brush dive
and the suction turbine will be
switched OFF. The travel drive
assembly remains activated. We
recommend to recharge the batte-
ries at the charging station as soon
as possible.
I Key for additional scrubbing and
vacuuming tool
Note: this key is only operable if
the Hakomatic is equipped with
the ”additional scrubbing and
vacuuming tool” option and the Ha-
ko service center has programmed
the machine accordingly.
Otherwise, ”-OP-” is displayed.
This key turns the water pump and
the suction turbine ON and OFF.
The water and the vacuuming hose
of the scrubbing tool have to be
connected previously.
46
3. 0 1 5
1. 2. 6. 1.
0 2 1 5.
9 9 9 9.
Scrubmaster is serviceable with
Scrubmaster is equipped with
… 14 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hako Scrubmaster B140R wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info