Bedienungsanleitung Harman Kardon AVR7200 (Seite 6 von 52) (Englisch)

502637

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

8 Surround Mode Selector: Press this button

to select from among the available surround mode

options for the major mode group selected. The

specific modes will vary based on the number of

speakers available, the major mode group and

whether the input source is digital or analog. For

example, press the Surround Mode Group Selector

7 to select a major mode grouping such as Dolby or

Logic 7, and then press this button to see the specific

mode choices that are available. For more information

on mode selection, see page 28.

9 Tuning Selector: Press the left side of the button

to tune lower-frequency stations and the right side of

the button to tune higher-frequency stations. When a

station with a strong signal is reached, the

TUNED

Indicator I will be lit in the Main Information

Display ˜.

)‹Button: When making system configuration

changes using the front-panel controls, press this but-

ton to scroll left through the available choices for the

option being adjusted.

! Tuner Band Selector: Pressing this button will

automatically switch the AVR 7200 to the Tuner mode.

Pressing it again will switch between the AM and FM

frequency bands. (See page 32 for more information

on the tuner.)

@ Set Button: When making system configuration

changes using the front-panel controls, press this but-

ton to enter a setting into the unit’s memory.

› Button: When making system configuration

changes using the front-panel controls, press this but-

ton to scroll right through the available choices for the

option being adjusted.

$ Preset Station Selector: Press this button to

scroll up or down through the list of stations that have

been entered into the preset memory. (See page 32

for more information on tuner programming.)

% Input Source Selector: Press this button to

change the input by scrolling up or down through the

list of input sources.

^ Tuner Mode Selector: Press this button to select

Auto or Manual tuning. When the button is pressed so

that the

AUTO Indicator J lights, the tuner will search

for the next station with an acceptable signal when the

Tuning Selector 9w

is pressed. When the

button is pressed so that the AUTO Indicator J is not

lit, each press of the Tuning Selector 9w

will

increase the frequency. This button may also be used to

switch between Stereo and Mono modes for FM radio

reception. When weak reception is encountered, press

the button until the

Stereo Indicator H goes out to

switch to Mono reception. Press and hold again to

switch back to Stereo mode. (See page 32 for more

information on using the tuner.)

& Optical 3 Digital Input: Connect the optical digital

output of an audio or video product to this jack.

* Input/Output Status Indicator: This LED indicator

will normally light green to show that the front-panel

Coaxial 3 Digital Input/Output Jack ( or the front-

panel Video 4 Input/Output Jacks Ó are operating

as inputs. When these jacks are configured for use as

an output, the indicator will turn red to show that the

jack may be used for recording. (See page 32 for more

information on configuring the front-panel jacks as out-

puts, rather than inputs.)

( Coaxial 3 Digital Input/Output: Connect the

coaxial digital input or output for a digital audio prod-

uct such as a portable audio player or video game to

this jack. The jack is normally an input, but may be

switched to an output for recording using the menu

system. See page 32 for more information.

Ó Video 4 Input/Output Jacks: These audio/video

jacks may be used for temporary connection to video

games or portable audio/video products such as cam-

corders and portable audio players. These jacks are

normally inputs, but may be switched to outputs for

recording using the menu system. See page 32 for

more information.

Ô Bass Control: Use this control to boost or reduce

the low-frequency output of the left/right front chan-

nels by as much as ±10dB. Set this control as you

find suitable to adjust to your specific taste or room

acoustics.

 Balance Control: Use this control to change the

relative volume for the front left/right channels.

NOTE: When multichannel surround modes are in use,

this control should be at the midpoint, or “12 o’clock”

position for proper operation.

Ò Treble Control: Use this control to boost or

reduce the high-frequency output of the left/right front

channels by as much as ±10dB. Set this control as

you find suitable to adjust to your specific taste or

room acoustics.

Ú Channel Adjust Selector: Press the button to

begin the process of adjusting the channel level out-

puts using the source currently playing through your

AVR. For complete information on adjusting the chan-

nel output level, see page 33.

Û Delay Adjust Selector: Press this button to

begin the process of adjusting the delay settings for

Dolby surround modes. See page 23 for more infor-

mation on delay adjustments.

Ù Digital Input Selector: Press this button to begin

the process of selecting a digital source for use with

the currently selected input. Once the button has been

pressed, use the

‹ or › Buttons )# to choose

the desired input and then press the Set Button @

to enter the setting into the unit’s memory. See page

30 for more information on digital audio.

ı Volume Control: Turn this knob clockwise to

increase the volume, counterclockwise to decrease the

volume. If the AVR 7200 is muted, adjusting volume

control will automatically release the unit from the

silenced condition.

ˆ Input Indicators: A green LED will light to the left

of the input that is currently the input source for the

AVR 7200.

˜ Main Information Display: This display delivers

messages and status indications to help you operate

the receiver. (See page 7 for a complete explanation

of the Information Display.)

¯ Remote Sensor Window: The sensor behind

this window receives infrared signals from the remote

control. Aim the remote at this area and do not block

or cover it unless an external remote sensor is

installed.

˘ Surround Mode Indicators: These LEDs will

light to show the surround mode and digital bitstream

in use. Note that depending on the specific combina-

tion of input sources and surround mode selected,

more than one indicator may light. (See page 28 for

more information.)

FRONT-PANEL CONTROLS

6 FRONT-PANEL CONTROLS

AVR 7200 OM 1/27/03 4:46 PM Page 6

Harman Kardon AVR7200 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info