Bedienungsanleitung Harman Kardon AVR7200 (Seite 42 von 52) (Englisch)

502637

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

42 CONFIGURING THE REMOTE

CONFIGURING THE REMOTE

7. The next display (Figure 42) and the subsequent

screens are where the actual macro programming

takes place. The words at the left side of the top

line of the display show the button that is being

programmed (e.g., the

Power On Button

one of the Macro Buttons

) and the indica-

tion at the right side of the top line shows the

number of macro steps available of 20 possible

steps. Following the instructions on the remote’s

LCD screen, press the first key you wish to be

transmitted in the macro. In our example, we first

want the AVR 7200 to turn on, so the

Power

Button

should be pressed.

Figure 42

8. Once the first command button for the macro has

been pressed, continue to press the buttons you

wish to be part of the macro, in the order they will

be used. Press each button within five seconds of

the last button, remembering to press the

Input

Selector

when you are changing device

functions. As the buttons on the remote are pressed,

the remote’s display screen will show the steps in

the macro as they are programmed (Figure 43).

Figure 43

9. For our example, we first want the AVR Power On

button pressed, followed by the TV Power On, fol-

lowed by the Cable Box On, followed by the selec-

tion of the Logic 7 mode. To do that, press the

buttons in this order:

•

Power On

• VID 2/TV

• Power On

• VID 3/Cable

• Power On

• AVR

• Logic 7

As each button is pressed to enter it into the

macro, you will see the button names appear and

then scroll up on the LCD display as your confir-

mation of the key entry (Figure 43).

10. When all commands for the macro have been

entered, press the

Set Button

to save the

macro. The display screen will show the button

to which the macro has been programmed and the

number of steps used, and the word

SAVED

will blink four times in the lower line of the LCD

display. When the display returns to normal, the

macro has been entered and the remote is ready

for operation.

11. If a macro has been programmed into the

Power

On Button

, it will play back anytime the

Power On button is pressed. As the macro plays,

you will see the steps appear in the remote’s LCD

display. Macros programmed into one of the four

discrete Macro buttons may be activated at any

time by pressing the appropriate button.

Erasing a Macro

Once a macro has been created and stored in the AVR

remote’s memory, you have the option of erasing it.

You may do this at any time by following these steps:

1. Press and hold the

Program Button

for

about three seconds while the message shown

in Figure 15 appears in the remote’s

LCD

Information Display

. Release the button

when the red light under the Set Button

appears.

2. The remote’s MAIN MENU message (Figure 16),

will appear in the LCD display and the Set Button

will remain illuminated in red. Press the

⁄

Navigation Button

three times so that

MACRO appears on the bottom line of the LCD

screen, as shown in Figure 37. Press the Set

Button

to enter the main macro menu

branch.

3. At the next menu screen (Figure 44), press the

⁄

Navigation Button n until the bottom

line in the remote’s LCD display reads ERASE A

MACRO. Press the Set Button

to begin the

process of erasing a macro.

Figure 44

4. The next display screen (Figure 45) is where you

select which macro will be erased. Press the

⁄

Navigation Buttons n until the number of the

macro you wish to erase appears. For this example

we will erase the Power On macro created in the

previous section. When the name of the macro to

be erased appears, press the

Set Button

Figure 45

5. The word ERASED will flash four times in the

bottom line of the remote’s LCD display, and then

the display will return to its normal condition. When

that happens the macro is erased and the remote

is returned to normal operation.

Read a Macro

To check the commands stored in the remote’s memory

for one of the buttons, follow these steps:

1. Press and hold the Program Button

for

about three seconds while the message shown

in Figure 15 appears in the remote’s

LCD

Information Display

. Release the button

when the red light under the Set Button

appears.

2. The remote’s MAIN MENU message (Figure 16),

will appear in the LCD display and the Set Button

will remain illuminated in red. Press the

⁄

Navigation Button

three times so that

MACRO appears on the bottom line of the LCD

screen, as shown in Figure 37. Press the Set

Button

to enter the main macro menu

branch.

3. At the next menu screen (Figure 46), press the

⁄

Navigation Button n until the bottom

line in the remote’s LCD display shows READ A

MACRO. Press the Set Button

to begin the

process of erasing a macro.

Figure 46

4. The next display screen (Figure 47) is where you

select the macro to be read. Press the

⁄

Navigation Button n until the name of the

macro you wish to read appears. For this example,

we will read back the Power On macro created in

a previous section. When the name of the macro

to be erased appears, press the

Set Button

Figure 47

5. As soon as the Set button is pressed, the first two

steps in the macro will be appear in the remote’s

LCD screen. You may then use the

⁄

Navigation Button n to step up or down

through the list of commands stored as the macro.

As you read the display, you will see

Device

Selector Buttons

appear in brackets,

(e.g., [AVR]). When the step in the macro is a

function, navigation or any other button, it will

appear next to the bracketed read-out of the

underlying device (e.g.,

[AVR] POWER ON).

6. When you are finished reviewing the macro’s

contents, press the

Set Button

to return

the remote to normal operation.

Punch-Through Configuration

Punch-through is a capability of the remote that

allows the Volume controls, Channel Up/Down buttons

or Transport keys (Play, Stop, Record, Fast Forward and

Reverse, and Skip Up/Down) to link to a different

device. For example, if your TV, cable box or satellite

receiver is connected through the AVR 7200, you will

READ A MACRO

POWER ON

MACRO

READ A MACRO

ERASE A MACRO

POWER ON

MACRO

ERASE A MACRO

[AVR]

[AVR] POWER ON

POWER ON 00/20

SELECT KEY PRESS

AVR 7200 OM 1/27/03 4:47 PM Page 42

Harman Kardon AVR7200 Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info