Bedienungsanleitung Harman Kardon AVR7200 (Seite 43 von 52) (Englisch)

502637

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

CONFIGURING THE REMOTE

CONFIGURING THE REMOTE 43

most likely want to use the AVR 7200’s volume control

commands even when the remote has been set to

issue all other commands for the video device. “Punch-

through” enables you to easily program the remote to

do this.

Volume Punch-Through

Follow these steps to enable the Volume Up/Down and

Mute controls from one device to be used when the

remote is otherwise programmed for a different device.

NOTE FOR VOLUME PUNCH-THROUGH: The

remote’s default settings are for the AVR 7200’s vol-

ume controls, to be used when any input or device is

selected, with the exception of the VID 2/TV button.

There is no need to program the remote for volume

punch-through for the AVR 7200’s controls with other

sources, such as DVD. To have the AVR 7200’s volume

commands used when the TV device is selected, follow

these steps:

1. Press and hold the

Program Button

for

about three seconds while the message shown

in Figure 15 appears in the remote’s

LCD

Information Display

. Release the button

when the red light under the Set Button

appears.

2. The remote’s MAIN MENU message (Figure 16),

will appear in the LCD display and the Set Button

will remain illuminated in red. Press the

⁄

Navigation Button n until PUNCH-

THROUGH appears on the bottom line of the

LCD screen, as shown in Figure 48. Press the

Set Button

to enter the main punch-through

menu branch.

Figure 48

3. At the next menu screen (Figure 49) press the

Set Button

to begin programming the

remote for Volume punch-through.

Figure 49

4. The next display screen (Figure 50) is where

you select the device that will receive the punch-

through commands. In our example, that is the

VID 2/TV button, as that is where we want the

AVR 7200’s volume controls to be active. Press

the

⁄

Navigation Button n until the name

of the base device appears and then press the Set

Button

Figure 50

5. At the next display screen (Figure 51), you will

select the device whose Volume Up/Down and

Mute commands will be used. Press the

⁄

Navigation Button n until the desired device’s

name appears to the right of the device in use. In

our example, that is the AVR 7200 (indicated by

AVR). When the desired combination of devices

appears, press the Set Button

Figure 51

6. When the Set button is pressed, the display will

change to show you that the new combination of

control commands is being saved to the unit’s

memory, as shown in Figure 52. The word

SAVED will flash four times and then the remote

will return to normal operation.

Figure 52

7. Once the punch-through is programmed, the

Volume Up/Down and Mute buttons of the second

device named will be used when those buttons

are pressed while the master device

is in use.

Returning the Volume Control Settings to

Default Operation:

If you wish to remove the Volume punch-through so

that the commands for Volume and Mute are returned

to the factory default setting, follow the steps shown

above, except that in Steps 4 and 5, select the same

device for both the

DEVICE IN USE on the left side

of the bottom line and the PUNCH-THROUGH

device. In the example used, the display to return the

remote to default settings will appear as shown in

Figure 53.

Figure 53

Channel Punch-Through

Channel punch-through allows the Channel Up/Down

buttons to send commands to a different device than

the one that has been selected for other commands.

For example, you may wish to use a cable box or

satellite receiver as the source for a VCR, so you would

want the Channel Up/Down Selectors X to trans-

mit commands to the cable box even though the other

button commands are programmed to operate the VCR.

To program the remote for Channel punch-through,

follow these steps. This example will show how to pro-

gram channel punch-through so that the commands

programmed for Channel Up/Down for the VID 3/

Cable device will be transmitted when the VID 1/VCR

device has been selected as the current device.

1. Press and hold the Program Button

for

about three seconds while the message shown

in Figure 15 appears in the remote’s

LCD

Information Display

. Release the button

when the red light under the Set Button

appears.

2. The remote’s MAIN MENU message (Figure 16),

will appear in the LCD display and the Set Button

will remain illuminated in red. Press the

⁄

Navigation Button n until PUNCH-

THROUGH appears on the bottom line of the

LCD screen, as shown in Figure 48. Press the Set

Button

to enter the main punch-through

menu branch.

3. At the next menu screen, press the

⁄

Navigation Button n until CHANNEL

appears on the bottom line of the LCD screen,

as shown in Figure 54. Press the Set Button

to begin programming the remote for Channel

punch-through.

Figure 54

4. The next display screen (Figure 55) is where you

select the device that will receive the punch-

through commands. In our example, that is the VID 2/

TV button, as that is where we want the cable

box’s channel controls to be active. Press the

⁄

Navigation Button n until the name of

the base device appears and then press the Set

Button

Figure 55

5. At the next display screen (Figure 56), you will

select the device whose Channel Up/Down com-

mands will be used. Press the

⁄

Navigation

Button n until the desired device name

appears to the right of the device in use. In our

example, that is the cable box. When the desired

combination of devices appears, press the

Set

Button

Figure 56

6. When the Set button is pressed, the display will

change to show you that the new combination

of control commands is being saved to the unit’s

memory, as shown in Figure 57. The word

SAVED will flash four times and then the remote

will return to normal operation.

PUNCH-THROUGH

VCR< -CBL

DEVICE IN USE

VCR

PUNCH-THROUGH

CHANNEL

PUNCH-THROUGH

TV< -TV

TV< -AVR [VOL]

SAVED

PUNCH-THROUGH

TV< -AVR

DEVICE IN USE

PUNCH-THROUGH

VOLUME

MAIN MENU

PUNCH-THROUGH

AVR 7200 OM 1/27/03 4:47 PM Page 43

Harman Kardon AVR7200 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info