Bedienungsanleitung Hendi 225059 (Seite 5 von 36) (Englisch, Polnisch)

741835

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

• a omnipolar switch with minimum between-con-

tacts aperture of the overvoltage category III (4000

V),

sized to the load and conforming to current

legal regulations, is ﬁ tted between the appliance

and the mains in the direct connection to the

mains;

• the omnipolar switch used for connection is easy

to reach when the appliance is installed;

• the yellow/green earth wire is not interrupted

by the switch;

• the power supply, when the appliance is operat-

ing, must not deviate from the rated voltage value

by ±10%;

• make sure that after inserting the power supply

cord into the terminal block it does not come into

contact with any of the cooking range’s hot parts.

• if the supply cable is damaged then it must be

replaced by the manufacturer or by your tech-

nical support or by a qualified person to avoid

any risk.

Connection to the water mains

(for ovens predisposed to humidiﬁ er solenoid-valve)

The appliance must be fed with softened drinking

water, with pressure in the range from 100 to 200 kPa

(1.0

- 2.0 bar). Water must have hardness from 0.5°F to

3°F (it is suggstible to use a softener as to avoid the

malfunction of the fan, the breakage of the heating

element and to reduce the formation of lime inside

the cooking chamber). Connection to the water

mains should be made through the threaded 3/4”

solenoid-valve on the rear (on the bottom) of the

appliance, ﬁ tting in between a mechanical ﬁ lter and

an on/off tap (before you connect the ﬁ lter, allow

a certain quantity of water to ﬂ ow out in order to

drain any waste from the pipe).

Connection to water tank

(for ovens predisposed to water pump)

To replace electrovalve with water pump (in ovens

with

optional predisposition to pump), follow the

steps below listed (image 1):

1. Remove back cover from oven.

2. Disconnect wiring cables from electrovalve.

3. Disconnect water tube (3) from electrovalve,

pressing e keeping pressed the edge of black

linking (quick insertion).

4. Remove the electrovalve unscrewing the screw

that ﬁ x it to oven’s frame.

5. Fix the pump (1) to the frame with the appropri-

ate support (2) and the two screws (4) included.

6. Connect the cables previously disconnected from

electrovalve to pump.

7. Connect the tube previously disconnected from

electrovalve to pump’s linking.

Connect the tube (6) with ﬁ lter and ballast (includ-

in “Pump kit”) to pump’s apron (7).

9. Replace back cover.

Warning:

To avoid limestone buildup into the cooking chamber,

we suggest to ﬁ ll the water tank with decalciﬁ ed water.

Check water level in the tank before activating the

pump and during its functioning. If pump works with-

out water in the tank, what occurs is abnormal noise

at first and then its breakage.

Fig. 1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hendi 225059 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info