Bedienungsanleitung Hitachi NR50AK (Seite 8 von 50) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

568872

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

English

work area, moving tool to another location, or after

use. It is very dangerous for a nail to be fired by

mistake.

24. When removing a nail which has become stuck, make

sure to first of all disconnect the hose and release

compressed air.

When removing a nail which has become stuck in the

nail outlet, first of all make sure to disconnect the

hose and release compressed air inside the power

tool.

Accidental firing of the nail could be very dangerous.

25. A female plug (air socket) should not be used in the

body.

If a female plug is installed in the body, the

compressed air sometimes can not be drawn when

the hose is disconnected so avoid this.

The tool and air supply hose must have a hose

coupling such that all pressure is removed from the

tool when the coupling joint is disconnected.

26. Use only genuine HITACHI heat treated nails for

HITACHI NR50AK.

Use only genuine HITACHI heat treated nails of 4.0 ×

40 mm (.157 × 1-9/16") and 4.0 × 50 mm (.157 × 2") for

HITACHI NR50AK to avoid serious injury from

ricocheting nails.

NAIL SELECTION

The use of any other nails and non-heat treated nails

could result in dangerous tool malfunction and/or

nail malfunction, causing serious injury.

27. Only for installation purpose of pre-punched holed

metal connector to wood stud.

28. Before each firing, be sure to position and insert the

first nail point through the metal hole.

This tool and nails are designed for metal connector

with pre-punched holes.

Drive nails into work surface only; never into materials

too hard to penetrate.

If the nail is not positioned and insert properly, it

could ricochet and hurt yourself or someone.

If you are not sure to position and insert the nail

through the metal hole, never drive nails.

Never drive nails into metal. Only drive into pre-

punched metal holes.

29. Always point first nail protruded from nose away

from yourself and others.

Keep your face, hands, feet and other body parts, as

well as those of other persons away from the nose

muzzle to avoid possible injury during use and

carrying.

SPECIFICATIONS

CAUTIONS

⅜ Use only genuine HITACHI heat treated nails for this NR50AK to avoid serious injury from ricocheting nails. The

use of any other nails and non-heat treated nails could result in dangerous tool malfunction and/or nail

malfunction, causing serious injury.

⅜ Select adequate nail size to meet proper metal hardware requirement needed for application, designed by metal

hardware manufacturer and regulated by the applicable building code.

Only nails shown in the Table below can be driven with this Nailer.

Type of power Piston reciprocating

Air pressure (Gauge) 4.9 – 8.3 bar (70 – 120 psi.)

Applicable nails ref. Fig.

Numbers of loadable nails 25 nails (1 strip)

Size 342 mm (L) × 333 mm (H) × 85 mm (W) (13-15/32” × 13-1/8” × 3–11/32”)

Weight 2.4 kg (5.3 lbs)

Nail-feeding method Spiral spring type

Hose (inside dia.) 8 mm (5/16”)

Dimensions of nails

Plastic-collated strip nails

Full-head nails

8.1 mm

(.319")

40 mm (1-9/16")

8.1 mm

(.319")

50 mm (2")

4.0 mm

(.157")

4.0 mm

(.157")

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi NR50AK Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info