Bedienungsanleitung Hitachi NR50AK (Seite 9 von 50) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

568872

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

English

(2) It is recommended using the recommended oil (SHELL

TONNA). Other applicable oils are listed. Never mix

two or more types of different oils.

3. Load nails

CAUTIONS

⅜ When loading nails into Nailer,

(1) do not depress trigger;

(2) do not depress push lever; and

(3) keep your face, hands feet and other body parts,

as well as those of other persons away from the

nose muzzle to avoid possible injury during usage

and carrying.

⅜ Do not insert different length sized nail strips at same

time. If do so, it could result in damaging nail strips

and jamming.

⅜ Always point first nail protruded from the nose away

yourself and others.

Keep your face, hands, feet, other body parts as well

as those of other person away from the nose muzzle

to avoid possible injury during usage and carrying.

(1) Align the nail head with nail length indicated on load

slot of the magazine cover, and then load the nails

(See Fig. 2).

(2) Slide the nail strip forward in the magazine.

The nail strip should pass over the nail stopper, which

means it is in proper position (See Fig. 3).

(3) Pull the nail feeder back with depressing the feeder

plate knob to push the nail strip.

NOTE

Use nail strip of more than 5 nails.

The Nailer is now ready to operate.

Removing the nails:

1 Depress the feeder plate knob slightly and slowly

slide the nail feeder forward.

2 Remove the nails from the Nailer.

CAUTION

To prevent unintentional operation, never touch the

trigger or place the top end of the push lever on a

work bench on floor. Also, never face the nail outlet

toward any part of a person.

STANDARD ACCESSORIES

(1) Hexagon bar wrench for M6 screw ...........................1

(2) Hexagon bar wrench for M5 screw ........................... 1

(3) Hexagon bar wrench for M4 screw ........................... 1

(4) Eye protector .............................................................. 1

(5) Oiler ............................................................................. 1

APPLICATIONS

CAUTIONS

⅜ Pre-punched holed metal connector to wood stud

installation only.

⅜ Never drive nails into metal or concrete.

⅜ Metal hardware with pre-punched holes to wood

stud installation only.

Straps, Joist hangers, framing anchors

PREPARATION PRIOR TO OPERATION

1. Prepare the hose

Be sure to use the hose provided with minimum

8 mm (5/16”) inside diameter.

NOTE

The air supply hoses must have a minimum working

pressure rating of 12.8 bar (180 psi.) or 150 percent of

the maximum pressure produced in the air supply

system, whichever is higher.

2. Check on safety

CAUTIONS

⅜ Unauthorized persons (including children) must be

kept away from the equipment.

⅜ Wear eye protector.

⅜ Check the retaining screws which fix the exhaust

cover, etc. for tightness.

Check the nailer for air leaks and defective or rusty

parts.

⅜ Check whether or not the push lever works correctly.

Also check whether or not any dirt has adhered to the

moving parts of the push lever.

⅜ Recheck on operational safety.

BEFORE USE

1. Check the air pressure

CAUTION

The air pressure must be constantly maintained at

4.9 – 8.3 bar (70 – 120 psi.).

Adjust the air pressure between 4.9 to 8.3 bar (70 –

120 psi.) according to the diameters and length of

nails and hardness of the wood being nailed. Pay

special attention to the output pressure, capacity,

and piping on the air compressor, so that air pressure

does not exceed the specified limit. Note that

excessive pressure may affect overall performance,

service life, and safety.

2. Lubrication

(1) Prior to operating this nailer, be sure to provide an air

set between the air compressor and this device.

Lubrication through the air set offers smooth

operation, extended service life, and anticorrosion.

Adjust the oiler so that a single drop of oil is supplied

at intervals of 5 to 10 nailing cycles.

Nail point

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi NR50AK Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info