Bedienungsanleitung Holzmann HBS 300J (Seite 20 von 30) (Deutsch, Englisch)

644517

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

ENGLISH

 Turn the upper blade pulley (8) several

times in a clockwise direction.

 Check the setting of the guide bearings

(28) again and re-adjust If necessary.

7.5.4 Setting the lower guide bearings

(29) (Fig. 12/13)

 Disassemble the saw table (15) (see

7.2)

 Undo the screw (40)

 Move the mount of the guide pins (29)

so that there is a gap of approx. 1mm

between the front edge of the pins (29)

and the gullet of the blade in front.

 Re-tighten the screw (40).

 CAUTION! The blade will be rendered

useless if the teeth touch the guide pins

while the blade is running.

 Undo the screws (38).

 Move the guide pins (29) towards the

blade so that there is a gap of max.

0,5mm between the guide pins (29)

and the blade (25). (The blade must

not jam).

 Re-tighten the Allen screws (38).

 Turn the lower blade pulley (7) several

times in a clockwise direction.

 Check the setting of the guide pins (29)

again and re-adjust if necessary.

7.6 Adjusting the upper blade guide

(11) (Fig. 2/14)

 Undo the fixing handle (20).

 Turn the adjustment wheel (19) to low-

er the blade guide (11) as close as pos-

sible to the workpiece to be cut (the

gap should be approx. 2-3mm).

 Re-tighten the fixing handle (20).

 Check the setting before each cut and

re-adjust if necessary.

7.7 Adjusting the saw table (15) to 90°

(8/15)

 Move the upper blade guide 811) to the

top.

 Undo the fixing handles (18).

 Set the angle (d) between the blade

(25) and the table (15).

 Tilt the table (15) by turning it so that

the angle between it and the blade (25)

is precisely 90°.

 Re-tighten the fixing handles (18).

 Undo the screw (52) of the pointer of

the dial scale (16), set the pointer to

exactly 0° and tighten the screw (52)

again.

7.8 Blade selection

The blade supplied with the bandsaw is de-

signed for all-purpose use. When you select a

blade you should have regard to the following

criteria:

 Use a narrow blade to cut tighter radii

than you can with a wider blade.

 Wide blades are used to saw straight

cuts. This is particularly important in

cutting wood because the blade has a

tendency to follow the grain of the

wood and thereby deviate easily from

the cutting line.

 Finely toothed blades provide smoother

cuts but are slower than coarse blades.

IMPORTANT: Never use warped or lacer-

ated blades!

7.9 Replacing the blade (Figure 16)

 Move the blade guide (11) into a posi-

tion approximately half way between

the table (15) and the machine frame

(24).

 Undo the fasteners (13) and open the

side cover (12).

 Remove the chain bar (2).

 Turn the tightening screw (9) anti-

clockwise to remove the tension from

the blade (25).

 Remove the blade (25) from the blade

pulleys (7,8) and take out through the

slot in the table (15).

 Fit the new blade (25), aligned centrally

on the blade pulleys (7,8).

 The teeth of the blade (25) must point

downwards in the direction of the table.

 Tension the blade (25) (see 7.2)

 Close the side cover (12) again.

 Mount the web panel (4) again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Holzmann HBS 300J Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info