Bedienungsanleitung Holzmann HBS 300J (Seite 21 von 30) (Deutsch, Englisch)

644517

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

ENGLISH

7.10 Changing the rubber tires on the

blade pulleys (Fig. 17)

After a certain time the rubber tires (3) on the

blade pulleys (7,8) will get worn by the sharp

teeth of the blades and must be replaced.

 Open the side cover (12).

 Remove the blade (25) (see 7.7)

 Lift the edge of the tire (3) with a small

screwdriver (f) and remove it from the

blade pulley (8).

 Repeat for the lower blade pulley (7).

 Fit the new rubber tire (3), mount the

blade (25) and close the side cover

(12) again.

7.11 Changing the table insert (Fig. 18)

To prevent increased likelihood of injury the

table insert (17) should be changed whenever

it is worn or damaged.

 Dismantle the saw table (15) (see 7.2).

 Push out the worn table insert (17).

 Fit the replacement table insert by fol-

lowing the above in reverse.

7.12 Extractor port

The bandsaw is equipped with an 100mm ex-

tractor socket (6) for extracting sawdust and

chips.

7.13 Adjusting the blade speed (Fig. 28)

The bandsaw can be operated at two blade

speeds. To change the position proceed as

follows:

 Slacken the drive belt (54) by turning

the hand wheel (4) in an anticlockwise

direction.

 Move the belt to the desired position on

the belt pulley (55) and the lower blade

pulley (7). The blade speeds are indi-

cated on the inside of the side cover.

 Tension the drive belt (54) again by

turning the hand wheel (4) in a clock-

wise direction. Important: Drive belts

must not be tensioned too much!

8. OPERATION

8.1 ON/OFF switch (Fig. 19)

 To turn the saw on, press the green

button (g).

 To turn the saw off again, press the red

button (h).

Your bandsaw has a switch with undervoltage

release. After a power failure you must reacti-

vate the switch

8.2 Parallel stop (Fig. 20/21)

The parallel stop is used as a guide in slitting.

 Place the parallel stop (23) onto the

chain bar (2) on the left or right and set

the desired dimension.

 Clamp the parallel stop in the desired

position by pressing the clamping lever

(27)

 The chain bar can be used for thinner

workpieces as shown in Figure 20 and

for thicker workpieces as shown in Fig-

ure 21.

8.3 Angular cuts (Figure 8/22)

To enable you to perform angular cuts parallel

to the blade (25), the table (15) can be tilted

forwards between 0° -45°.

 Undo the fixing handle (18).

 Tilt the saw table (15) forward until

required angle value has been set on

the man scale (16).

 Re-tighten the fixing handle (18).

 Important: When the table (15) is tilt-

ed, place the parallel stop (23) to the

right of the blade (25) looking in the di-

rection in which you are working, on

the side pointing downwards. (provided

the workpiece is wide enough) in order

to stop the workpiece from slipping off.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Holzmann HBS 300J Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info