Bedienungsanleitung Holzmann HBS 300J (Seite 22 von 30) (Deutsch, Englisch)

644517

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

ENGLISH

9. OPERATION ADVICES

Important! After every new adjustment we

recommend you to make a trial cut in order to

check the new settings.

 For all cutting operations it is important

to position the blade guide (11) as

close as possible to the workpiece.

 Always guide the workpiece with both

hands, holding it flat on the table (15)

in order to prevent the blade (25) from

jamming.

 Feed the workpiece at a uniform speed

that enables the blade to cut through

the material without difficulty and with-

out blocking.

 Always aim at making a complete cut in

one pass rather than in a stop-and-go

operation requiring the workpiece to be

withdrawn. If you have to withdraw the

workpiece, switch off the bandsaw first

and wait for the blade (25) to stop be-

fore freeing the workpiece.

 The workpiece must always be guided

by the longer side during cutting.

Important! When handling narrower work-

pieces, it is essential to use a push stick. The

push stick (28) must always be kept close at

hand at then hook(29) provided for that pur-

pose on the side of the saw (Fig. 27).

9.1 Longitudinal cuts

Longitudinal cutting (also known as slitting) is

when you use the saw to cut along the grain of

the wood.

 Place the parallel stop (23) to the left of

the blade (25), as far as possible, for

the width required.

 Lower the blade guide (11) down to the

workpiece.

 Switch the saw on.

 Press the edge of the workpiece with

your right hand to hold it securely

against the parallel stop (23) and flat

on the table (15).

 Guide the workpiece along the parallel

stop (23) and through the blade (25) at

a uniform speed.

 Important: Long workpieces must be

secured against falling off the table at

the end of the cut-

9.2 Freehanded cuts (Figure 25)

One of the most outstanding features of a

bandsaw is the ease with which it allows you to

make curved cuts and radii.

 Lower the blade guide (11) down to the

workpiece.

 Switch on the saw.

 Hold the workpiece securely on the

table (15) and guide slowly through the

blade (25).

 Freehanded cuts should be made at low

feed speed so that you can guide the

blade (25) along the required line.

 It often pays to first cut off surplus

curves and corners up to about 6mm

from the cutting line.

 In the case of curves which are too

tight for the blade to cut correctly, it

can help to make a series of close-lying

cuts at right angles to the curved line.

When you saw the radius the material

simply will drop off.

10. MAINTENANCE

Important! Pull out the power plug first.

Remove the dust and dirt regularly from the

machine. Cleaning is best carried out with a

fine brush or a cloth.

Never use caustic agents to clean plastic parts.

11. ORDERING SPARE PARTS

Please provide the following information on all

orders for spare parts:

 Model/type of the machine

 Date of acquisition

 Serial number of the machine

 Spare part(s) marked on exploded

drawing

 Required spare part numbers listed

additionally.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Holzmann HBS 300J Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info