Bedienungsanleitung Hormann Schuifhekaandrijving (Seite 29 von 132) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

538730

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

DIL switch 5/DIL switch 65.8.4

SE 2 safety device (closing):

See f Figure 7.5

The functions of the safety device are set with DIL switch 5 in

combination with DIL switch 6.

5 ON Activation kit for closing edge safety device or

photocell with testing

5 OFF

8k2 resistance contact strip•

No safety device (8k2 resistance between •

terminals 20/73, delivery status)

6 ON Brief, delayed reversing in the OPEN direction (for

photocell)

6 OFF

Brief, immediate reversing in the OPEN direction

(for SKS)

5.8.5 DIL switch 7

SE 3 protective device (closing):

See f Figure 7.6

Delayed reversing to CLOSE end-of-travel position.

7 ON Dynamic 2-wire photocell

7 OFF

Static photocell without testing •

No safety device (wire jumper between •

terminals 20/71, delivery status)

DIL switch 8/DIL switch 95.8.6

The functions of the operator (automatic timed closing/

warning phase) and the function of the option relay are set

with DIL switch 8 in combination with DIL switch 9.

See f Figure 7.7a

8 ON 9 ON Operator

Automatic timed closing, advance

warning phase for each gate movement

Option relay

Relay clocks rapidly during the advance

warning phase, normally during the travel

phase and is OFF during the hold-open

phase.

See f Figure 7.7b

8 OFF 9 ON Operator

Automatic timed closing, advance

warning phase only for automatic timed

closing

Option relay

Relay clocks rapidly during the advance

warning phase, normally during the travel

phase and is OFF during the hold-open

phase.

See f Figure 7.7c

8 ON 9 OFF Operator

Advance warning phase for every gate

travel without automatic timed closing

Option relay

Relay clocks rapidly during the

advance warning phase, normally

during the travel phase.

See f Figure 7.7d

8 OFF 9 OFF Operator

No special function

Option relay

Relay picks up in the CLOSE end-of-

travel position.

NOTE:

Automatic timed closing is only possible from the determined

end-of-travel positions (full or partial opening). Automatic

timed closing is deactivated if it fails three times. The operator

must be restarted with an impulse.

DIL switch 105.8.7

Effect of the SE 3 protective device as a through-trafﬁc

photocell with automatic timed closing

See f Figure 7.8

This switch is used to set the SE3 protective device as a

through-trafﬁc photocell with automatic timed closing.

7 ON The photocell is activated as a through-trafﬁc

photocell, after the photocell has been passed,

the hold-open phase is reduced.

7 OFF

The photocell is not activated as a through-

trafﬁc photocell. If, however, automatic timed

closing is activated and the photocell

interrupted after the hold-open phase has

elapsed, the hold-open phase will be reset to

the preset time.

DIL switch 115.8.8

Setting up the reversal limits

See Chapter f Reversal limit, page 28

DIL switch 125.8.9

Starting point for slow speed when opening and closing:

See Chapter f Changing the starting point for slow speed

when opening and closing, page 28

TR10A059-C RE / 10.2008 29

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hormann Schuifhekaandrijving Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info