Bedienungsanleitung Hormann Schuifhekaandrijving (Seite 28 von 132) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

538730

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

The learned force setting must be checked using a 2.

suitable force measuring device to make sure that the

values are permissible within the application scope of the

European Standards EN 12453 and EN 12445 or the

corresponding national regulations.

5.6 Changing the starting point for slow speed

when opening and closing

The slow speed length is automatically set to a basic value of

approx. 500 mm before the end positions after the end

positions have been learned. The starting point can be

reprogrammed from a minimum length of approx. 300 mm up

to the entire gate length (see Figure 7.2).

Setting the positions for slow speed:

The end-of-travel positions must be set and the gate is in 1.

the CLOSE end-of-travel position.

DIL switch 2 must be OFF.2.

Set 3. DIL switch 12 to ON to set the starting position for

slow speed.

Press print button 4. T.

The gate will travel normally in press-and-release

operation towards the OPEN direction.

When the gate passes the required position for the start 5.

of slow speed, brieﬂy press print button P.

The gate will move at slow speed for the remaining

distance until in the OPEN end-of-travel position.

Press print button 6. T again.

The gate will again travel normally in press-and-release

operation towards the CLOSE direction.

When the gate passes the required position for the start 7.

of slow speed, brieﬂy press print button P.

The gate will move at slow speed for the remaining

distance until in the CLOSE end-of-travel position.

Set 8. DIL switch 12 to OFF.

The slow speed starting point settings have now been

completed.

NOTE:

The starting points for slow speed can also be set to

"overlap"; in this case, the entire leaf movement is in slow

speed.

Changing the starting points for slow speed deletes the

already learned forces. After a change has been made, the

green LED ﬂashes to signal that the forces must be learned

again.

Both of the following procedures must be conducted f

three times.

Learning the forces to the OPEN end-of-travel position:

Press print button f T once.

The operator automatically moves into the OPEN end-of-

travel position.

Learning the forces to the CLOSE end-of-travel position:

Press print button f T once.

The operator automatically moves into the CLOSE end-

of-travel position.

5.7 Reversal limit

During operation of the gate in the CLOSE direction, it must

differentiate between two options: whether the gate contacts

the limit stop (gate system stops) or an obstruction (gate

reverses direction). The limit range can be adjusted as follows

(see Figure 7.3).

Setting the reversal limit:

Set DIL switch 111. to ON.

The reversal limit can now be set step-by-step.

Brieﬂy press print button 2. P to reduce the reversal limit.

Brieﬂy press print button T to increase the reversal limit.

During the procedure to learn the reversal limits, the

green LED displays the following settings:

1x ﬂashing Minimum reversal limit, the green LED

ﬂashes once

10x ﬂashing Maximum reversal limit, the green LED

ﬂashes max. 10 times

Set DIL switch 113. back to OFF to store the set reversal

limit.

5.8 Overview and settings of the DIL switches

Changes to the DIL switch settings are only permissible under

the following conditions:

The operator is at a standstill.•

The advance warning or hold-open phase is not active.•

The DIL switches must be set as described below in

accordance with national regulations, the desired safety

devices and the on-site circumstances.

DIL switch 15.8.1

Installation direction:

See Chapter f Preparation, page 26

DIL switch 25.8.2

Installation direction:

See Chapter f Learning the gate‘s end-of-travel positions,

page 26

5.8.3 DIL switch 3/DIL switch 4

SE 1 safety device (opening):

See f Figure 7.4

The functions of the safety device are set with DIL switch 3 in

combination with DIL switch 4.

3 ON Activation kit for closing edge safety device or

photocell with testing

3 OFF

8k2 resistance contact strip•

No safety device (8k2 resistance between •

terminals 20/72, delivery status)

4 ON Brief, delayed reversing in the CLOSE direction

(for photocell)

4 OFF

Brief, immediate reversing in the CLOSE direction

(for SKS)

TR10A059-C RE / 10.2008

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hormann Schuifhekaandrijving Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info