Bedienungsanleitung Hormann Schuifhekaandrijving (Seite 26 von 132) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

538730

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

Connecting a cut-out to stop the operator 4.10.3

(STOP or emergency OFF circuit)

A cut-out with normally closed contacts (switching to 0 V or

volt-free) is connected as follows (see Figure 4.3):

Remove the wire jumper inserted at the factory between 1.

terminal 12 and terminal 13.

Terminal 12: STOP or emergency OFF input –

Terminal 13: 0 V, allows normal function of the –

operator

Connect switching output or ﬁrst contact at terminal 2. 12

(STOP or emergency OFF input).

Connect 0 V (ground) or second contact to terminal 3. 13

(0 V).

NOTE:

By opening the contact, any travel cycles in progress are

immediately halted and permanently prevented.

Connecting a warning lamp*4.10.4

See f Figure 4.4

(*Accessory, not included as standard equipment!)

A warning lamp or CLOSE end-of-travel signal can be

connected via the volt-free contacts on the Option connector.

The voltage at the 24 V DC connector can be used for

operation (e.g. warning signals prior to and during gate travel)

with a 24 V lamp (max. 7 W).

NOTE:

A 230 V warning lamp must be directly supplied with power

(see Recording the CLOSE end-of-travel position via the limit

switch, page 27).

Connecting safety/protective devices4.10.5

See f Figure 4.5-4.7

Safety devices such as photocells/closing edge safety

devices (SKS) or 8k2 resistance contact strips can be

connected:

SE1 In the opening direction, safety device with testing

or 8k2 resistance contact strip.

SE2 In the closing direction, safety device with testing or

8k2 resistance contact strip.

SE3 In the closing direction, photocell without testing or

dynamic 2-wire photocell, e.g. as a through-trafﬁc

photocell.

The selection for the 3 safety circuits can be set via the DIL

switches (see Overview and settings of the DIL switches ,

page 28).

Terminal 20 0 V (voltage supply)

Terminal 18 Test signal

Terminals 71/72/73 Signal of safety device

Terminal 5 +24 V (voltage supply)

NOTE:

Safety devices without a testing unit (e.g. static photocells)

must be tested twice a year. They may only be used to

protect property!

BUS connection4.10.6

See f Figure 4.8

Putting into Service5

Before initial operation, check that all the connecting f

leads are correctly installed at the connecting terminals.

Open the gate halfway. f

Engage the operator. f

General5.1

The control is programmed via the DIL switches. Changes to

the DIL switch settings are only permissible under the

following conditions:

The operator is at a standstill.•

The advance warning or hold-open phase is not active.•

Overview of set-up mode5.2

Set-up mode is described in the following chapters:

• Preparation, page 26

• Learning the gate‘s end-of-travel positions, page 26

– Recording the CLOSE end-of-travel position via the

limit switch, page 27

– Recording the OPEN end-of travel position, page 27

– Recording the partial opening end-of-travel position,

Page 27

• Learning the forces, page 27

• Changing the starting point for slow speed when opening

and closing, page 28

• Reversal limit, page 28

5.3 Preparation

All the DIL switches must be in the factory setting, i.e. all f

the switches must be at OFF (see Figure 5).

Change the following DIL switches:

DIL switch 1: f Installation direction (see Figure 5.1)

ON Gate closes to the right

(as viewed from the operator)

OFF

Gate closes to the left

(as viewed from the operator)

Accordingly f set DIL switches 3-7: Safety devices (see

Chapter DIL switch 3/DIL switch 4 to DIL switch 7 from

page 28).

5.4 Learning the gate's end-of-travel positions

DIL switch 2: f Set-up mode (see Figure 6.1)

ON Learning the gate travel

OFF

NOTE:

The safety devices are not active during set-up mode.

TR10A059-C RE / 10.2008

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hormann Schuifhekaandrijving Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info